The Mercedes-Benz G 63 AMG 6x6 represents a singular vision to create the boldest and toughest all-terrain vehicle ever. Traxxas captures the spirit and no-compromise approach of the Mercedes-Benz G 63 AMG 6x6 with an officially licensed detailed scale replica built on the proven TRX-6 platform. Six drive wheels, three T-Lock™ remote-locking differentials, portal axles, high/low transmission, 6 aluminum long-travel shocks, and a stunningly accurate body with brilliant LED lighting make this the most advanced and capable RC crawler ever to hit the trail.
TRX-6® Scale and Trail™ Crawler with Mercedes-Benz® G 63® AMG 6x6 body:1/10 scale 6WD electric trail truck, Ready-To-Drive®, with TQi™ Traxxas Link™ enabled 2.4GHz radio system, XL-5 HV ESC (fwd/rev), and Titan® 550 motor.
Officially Licensed 1979 Chevrolet® K5 Blazer Body
Scale details: deep-inset front grille, chrome bumpers, side mirrors, door handles, side trim and wipers
LED-ready headlights, tail lights, and side markers
Authentic decal sheet
Full Nylon composite wheel wells and floor pans
Clipless Body mounting
Clipless design for smooth body appearance
Rugged internal body cage for added rigidity
Body details mount directly to internal frame
Trail-tuned XL-5™ HV Waterproof Electronic Speed Control
Fully waterproof design
Five drive profiles
Sport Mode — forward / brake / reverse
Race Mode — forward / brake / no reverse
Training Mode™ - 50% forward / 100% brake / 50% reverse (patented)
Trail Mode — forward / brake / reverse / with trail-tuned drag brake in neutral
Crawl Mode — forward / instant reverse - no neutral with 100% hill holding brake
Traxxas EZ-Set® one-button setup
Large, efficient heat sink
Wide voltage latitude 6–7 cell NiMH (7.2–8.4 V) and 2–3s LiPo (7.4–11.1 V)
Two stage low voltage protection (LVD)
Titan® 550 Motor
Powerful Titan 21T reverse rotation motor with internal cooling fan
Precision, preset gear mesh adjustments
Motor retention separate from gear mesh
Portal Axles
Increase ground clearance
Eliminate torque twist
Steel gears
Improve axle geometry and reduce strain on driveshafts
Drivetrain
Full-time shaft driven 4-wheel drive
Tough 6 mm stub axles
Steel front CV driveshafts
Hardened steel rear axle shafts
Remote locking steel gear differentials with cable-actuation
Steel gear transfer case
Factory-Installed Long Arm Lift Kit
Increases ground clearance over 1″
Maintains precise steering geometry
Accommodates oversize 2.2″ wheels and tires
TQi™ 2.4 GHz Radio System
4-channel transmitter
5-channel micro receiver (6533) with fail-safe security and integrated telemetry ports
Compatible with optional TQi Traxxas Link Wireless Module (6511) to access full Traxxas Link app functionality (sold separately)
Automatically stores and loads settings for up to 30 Traxxas Link enabled models
Exclusive Cruise Control feature for extended trail driving
Adjustable steering and throttle sensitivity (exponential)
Adjustable steering and throttle endpoints
Patented waterproof receiver box with easy-access plug
Reinforced Steel Ladder Frame
Full-length 1.5 mm thick steel frame rails
Bumpers adjust fore and aft
Rugged rock rails adjust for width
Wire routing clips integrated into frame rails
Innovative Battery Compartment
Hinged battery strap allows quick and easy battery access
No pins to lose
Accommodates different height batteries
Accepts full-size long battery packs
Integrated compartment accepts smaller 1/16 scale batteries (with optional strap)
Secondary front battery tray accepts smaller 1/16 scale batteries (with optional strap)
Transmission
Two speed high/low range with remote shifting
Dual horizontal shafts
Twin friction plate slipper clutch
Easily removed for servicing
Steering
Chassis mounted 2075X metal gear digital servo
Superior 45° steering angle
Direct steering (no servo saver)
Steering geometry corrected for bump steer
Suspension
Front — 3 link with panhard
Rear — Triangulated 4 link
Heavy-duty rod ends with steel hollow balls
5 mm diameter steel link rods with 4 mm threaded ends
Extended Aluminum GTS Shocks
Oil-filled coilover GTS shocks exclusive to TRX-4 chassis
Extra-long aluminum bodies for greater articulation
Silver-anodized aluminum bodies
Threaded bodies with collars easily adjust ride height
Silky smooth damping for the toughest trails
O-ring cap seal and dual X-ring shaft seals
Oversize Wheels and Tires
2.2″ chrome mag wheels wheels with hub inserts
Pre-mounted 2.2″ Canyon Trail tires with trail-tuned foam inserts
Trail tuned S1 rubber compound
12 mm steel hex
Sealed Ball Bearings
Hex hardware with Rust-Resistant Black Oxide Coating
Requires Battery and Charger (Sold Separately)
Traxxas TRX-4 High Trail RC Crawler with '79 Ford F-150 Body
The Traxxas TRX-4 1/10 High Trail Edition RC Crawler with '79 Ford F-150 Ranger XLT Truck Body has been designed to offer scale performance and adventure. Thanks to its factory-installed Long Arm Lift Kit and oversize tires, the highly detailed 79 Ford F-150 Ranger XLT body stands over an inch taller than the standard TRX-4 chassis. The F-150's extended wheelbase further enhances the TRX-4’s legendary off-road capability for better performance on the trail. To further the appearance, this truck uses the Traxxas Clipless Body Mounting for added scale realism. The TRX-4 High Trail Edition is the perfect vehicle for the driver who wants it all: extreme all-terrain capability, stunning scale looks, and extreme durability.
This High Trail Edition TRX-4 uses portal axles, 110mm threaded shocks and a lift kit for extreme ground clearance. Oversized Canyon Trail tires are mounted to chrome 2.2" wheels to improve both performance and ground clearance. When the going gets tough, use your transmitter to shift into low range for incredible 4-wheel drive pulling torque. Shift into high range for blasting down the trail. Traxxas gives you the versatility to lock and unlock the front and rear differentials to suit your driving needs directly from your transmitter. Leave the differentials unlocked for relaxed driving on the trail with smooth, tight turning and better handling at high speeds. When the trail gets technical, lock the front and rear differentials, or just the front, for superior grip over extreme terrain.
New @ford F-150 Ranger XLT High Trail Edition | @Traxxas TRX-4
Features:
Molded Scale Detail: The 1979 Ford F-150 Ranger XLT Pickup Body comes with authentic-looking chrome wheels, side mirrors and windshield wipers.
Clip-less Body Mounting System: Traditional posts and body clips are gone, and instead an integrated quick-release system secures the body invisibly. The hidden mechanism holds tight on the trail yet releases in just seconds to access the chassis.
Trail-tuned XL-5 HV Waterproof Electronic Speed Control: HV electronic speed control brings 3s LiPo capability for strong efficient running. The powerful 21T Titan motor provides torque for hauling heavy loads and climbing steep grades.
Factory-Installed Long Arm Lift Kit: The lift kit not only gives you an extra inch of ground clearance but also maintains the TRX-4's suspension geometry.
Extended Wheelbase: The K10’s steel frame rails extend the wheelbase out to 336mm to capture the pickup’s real-world proportions perfectly.
The Power of Portals: The K10’s portal axles work in tandem with the Lift Kit to lift the truck for huge center ground clearance. The portal axles’ internal gear reduction virtually eliminates torque twist, keeping the K10 straight and on course.
Extended Aluminum GTS Shocks: These shocks are 20mm longer than the standard GTS shocks. The threaded shock bodies are silver-anodized to deliver silky-smooth dampening.
Oversize Wheels and Tires: The aggressive Canyon Trail tires feature large lugs for increased grip with foam inserts for realistic trail performance. Slotted chrome Mag wheels come with replica locking hubs to conceal the wheel nuts.
Sealed Ball Bearings: Reliable sealed ball bearings are used throughout the chassis for long-lasting performance.
Specifications:
Scale: 1/10
Length: 22.30inches (566mm)
Track Width (Front/Rear): 10.60inches (270mm)
Center Ground Clearance: 4inches (99mm)
Height (Overall): 10.82inches (275mm)
Wheelbase: 13.23inches (336mm)
Weight (w/o Battery): 7.38lbs (3.35kg)
Shock Length (Front/Rear): 4.33inches (110mm)
Wheels (Front/Rear): 2.2x1.34inches (56x34mm)
Tires (Front/Rear): 5.3x2.14inches (135x54mm)
Approach Angle: 73.5°
Departure Angle: 49.67°
Breakover Angle: 67°
Hex Size: 12mm
Gear Pitch: 32P
Battery Tray Size (LxWxH): 158.75x47x23/26mm
Includes:
(1) Traxxas TRX-4 1/10 High Trail Edition RC Crawler with '79 Ford F-150 Ranger XLT Body
(1) TQi 2.4 GHz 4-Channel Transmitter
Maintenance Tools
Needed to Complete:
(4) "AA" Batteries (for transmitter)
(1) NiMH Battery (4-7 cell) or LiPo Battery (2S/3S)
(1) Compatible Battery Charger
Originally introduced in 1966 as a 4X4 compact SUV, the Ford Bronco matured as a full-size truck in the late 1970s, cementing its status as a rugged off-roader. Traxxas honors the classic 1979 Ford Bronco with this beautifully detailed and faithful reproduction mounted on the incredibly capable TRX-4® chassis. From the chrome wheels and bumpers to the gorgeous Sunset or red graphics, the TRX-4 recaptures the Bronco’s iconic era with the toughness and technology that could only come from Traxxas.
1/10 Scale 4X4 Trail Truck, Fully-Assembled, Waterproof electronics,Ready-To-Drive®, with TQi™ 2.4GHz 4-channel Radio System, XL-5 HV Speed Control,Hi/Low Transmission, Remote Locking Differentials, and painted body
Axial SCX24 2021 Ford Bronco - Hard Body 1/24 Scale Mini Scale Crawler!
The Axial SCX24 2021 Ford Bronco comes out of the box fully assembled and ready-to-run. The SCX24 '21 Bronco features an exceptionally detailed and extra-durable ABS hard body! This authentic scale body is available in three color options based on current Ford Bronco factory colors. Details include molded door handles, mirrors, roof rails, a mounted spare tire and an optional second decal sheet to allow a personalized finish. Serious scale modelers will find that this Ford Bronco not only looks great and performs well, but also brings next level realism to the SCX24 platform. Complementing the detail of the scale Ford Bronco body, Axial includes officially licensed Factory Ford Wildtrak wheels and Nitto Trail Grappler M/T tires.
The SCX24 Bronco is built on the proven and easy to drive SCX24 chassis. The SCX24 makes it easy to find RC adventures. Go crawling on your desk. Turn a messy room into an obstacle course. Build an indoor "crawl course table" - or take your SCX24 outdoors and set up an exciting trail with a few holes, twigs, and rocks. Whatever course you follow, the SCX24 chassis meets every challenge with full-time 4-wheel drive, a trail-taming 3-link front/4-link rear suspension, and much more. Realistic steel frame rails stand up to hard knocks. Worm gears on the axles increase ground clearance. Steel front and rear axles, front stub axles and steel dogbones let you crawl and climb with confidence. Power is supplied by a Dynamite 88T 180-size motor and 2S LiPo battery, while a 3-channel Horizon Hobby 2.4GHz radio system is included for precise, dependable control. So everything you need to hit the trails is in the box!
Axial SCX24 Ford Bronco
Features:
Factory-assembled and ready-to-run, with 3-channel radio, 180 brushed motor, servo, ESC/receiver unit and "AA" transmitter batteries included
Officially licensed Ford Bronco ABS hard body with molded door handles, mirrors, roof rails, and a tire mount with spare tire
Bonus second decal sheet for optional customization
Nitto Trail Grappler M/T tires mounted on Factory Ford Wildtrak wheels
Working lights in front, with molded lenses on all four corners of the body
True full-time 4-wheel drive
Durable solid axle front and rear suspension and coilover shocks for optimal handling and crawling performance
Worm drive gears in front and rear differentials increase ground clearance
Sturdy steel C-channel frame rails with bracing for added strength and proper alignment
Durable steel axles provide strength and durability to match tough climbs and rough trails
2-Year limited warranty (see product manual for details)
Specifications:
Height: 4.625" (117 mm)
Front Track: 3.938 in (100.0mm)
Width: 3.875" (98 mm)
Rear Track: 3.938 in (100.0mm)
Wheelbase: 5.19" (132 mm)
Length: 8.75" (222 mm)
Includes:
(1) Axial® SCX24™ Ford Bronco 1/24 Scale 4WD RTR
(1) Horizon Hobby® 2.4GHz 3-Channel Radio System
(1) Axial® AS-1 Micro Servo
(1) Horizon Hobby® ESC/Receiver Combo
(1) Dynamite® USB LiPo Charger
(1) Dynamite® 88T 180-Size Brushed Electric Motor With Pinion
(1) Dynamite® 350mAh 2S 30C 7.4V LiPo Battery
(4) AA Batteries for Transmitter
(2) Decal Sheets
(1) Product Manual
Needed to Complete:
Everything you need to drive is included
The Furitek SCX24 Stinger Brushless Power System with 1212-3450kV Brushless Motor is a great way to get a light weight, high torque power system. This incredible combo includes the Furitek Micro Komodo Motor (FTK-FUR-2100). Don't let the size of this motor fool you, this 12-pole motor was specifically designed to provide high torque at low RPM. The included Lizard Pro ESC allows you to get the most out of this small but mighty motor.Features:
Designed specifically for the Axial SCX24
Includes the Furitek Micro Komodo Motor FTK-FUR-2100
12-pole motor design allows for high torque at low RPM
Includes Micro Komodo Motor Mount
Includes the Furitek Lizard Pro ESC
Includes:
(1) Lizard Pro 30A/50A Brushed/Brushless ESC
(1) Bluetooth module
(1) Micro Komodo 1212-3450KV brushless motor
(1) 11T 0.3M CNC Brass Pinion
(1) CNC aluminum motor mount
COMPATIBILITY:
Axial SCX24
The SCX24 Deadbolt 4WD is the first Axial off-roader in 1/24 scale. At less than 8" long, it's the perfect rig to take along on outdoor OR indoor adventures - offering factory-assembled ease, scale looks, and confident handling on any trail.
Features
Includes 3 channel radio system, ESC and transmitter batteries
Includes motor and on-board LiPo battery
Realistic narrow-stance rock crawler body in olive green or red
Molded roll cage with realistic light bar
Realistic driver figure and many other scale details
Officially licensed KMC XD229 Machete Crawl wheels
Officially licensed Nitto Trail Grappler M/T tires (S30 compound, large block tread)
Full-time 4WD
Splined and sleeved front and rear drive shafts allow for maximum suspension travel while keeping the power to the wheels
Steel front and rear axles, front stub axles and dogbones provide strength and durability
Rugged steel C-channel frame rails with bracing keep everything rigid and aligned
Front and rear axles consist of a two-piece, molded plastic solid axle design
3-Link front and 4-link rear suspension supply optimal handling
Coil-over shocks with simulated reservoir and durable plastic suspension links deliver proven Axial crawling performance
Front and rear differentials each house a worm gear setup to power the axles and create higher ground clearance. Worm gear drive also provides a low gear ratio to reduce torque twist
Two LEDs in the front bumper for night driving
Needed to Complete
Nothing! Everything you need to begin having fun with your 1/24 scale Deadbolt is included!
What's in the Box?
(1) SCX24™ Deadbolt™ 1/24 Scale 4WD Truck
(1) Axial AE-6 ESC/receiver combo (installed)
(1) Dynamite® 88T brushed electric motor (installed)
(1) Axial AS-1 steering servo (installed)
(1) Axial® AX-4 2.4GHz 3-channel radio
(4) AA transmitter batteries
(1) 350mAh 2S 7.4V LiPo battery
(1) USB LiPo charger
(1) Product Manual
Overview
The SCX24™ Deadbolt™ 4WD is the first Axial® off-roader in 1/24 scale. At less than 8" long, it's the perfect rig to take along on your hiking, camping, and other outdoor and indoor adventures — offering factory-assembled ease, scale looks, and confident handling on any trail.
Even new modelers driving the SCX24 chassis will be well-equipped to tackle tough climbs and rough trails. Like the larger SCX10™ II chassis, this smaller version uses plenty of steel components — from the C-channel frame rails to the front and rear axles and dogbones. Even over off-road, mountainous, rocky and desert terrain, it has the strength to keep pushing onward and upward.
For the most reliable handling, the SCX24 chassis features a three-link front and four-link rear suspension. The combination of coil-over shocks and durable plastic suspension links delivers Axial-worthy crawling performance even at this small scale. The worm gear drive setup permits a high ground clearance plus a low gear ratio that reduces torque twist.
Powered by an included 180-size motor and LiPo battery, the SCX24 Deadbolt shows off competence and charisma on the trails. Check out that Deadbolt body — with its narrow stance, bulging hood, realistic driver figure, and molded roll cage with realistic light bar. The realism continues right down to the ground, where you'll find licensed KMC XD229 Machete Crawl wheels wrapped in Nitto Trail Grappler tires.
Adding even more to its beginner appeal, the SCX24 Deadbolt comes 100% complete and ready to run. Everything required for action is in the box: assembled and finished vehicle; Axial 3-channel 2.4GHz radio system with servo and ESC/receiver unit; Dynamite® 88T brushed electric motor and 350mAh 2S 7.4V LiPo battery; USB LiPo charger; and even four AA cells for the transmitter!
STEEL C-CHANNEL CHASSIS FRAME RAILS
Just like the 1/10th scale SCX10™ II platform, the SCX24™ chassis features rugged and sturdy steel c-channel frame rails with bracing to keep everything intact and aligned.
DYNAMITE® 88T BRUSHED MOTOR
The Dynamite 88T brushed electric motor provides the right amount of torque to help ascend steep climbs. It's mated to a steel motor mount to keep flex to a minimum, which helps protect the gears.
WORM GEARS
The front and rear differentials each house a worm screw and worm gear setup to get the power to the axles and create higher ground clearance.
DURABLE STEEL AXLES
Steel front and rear axles, front stub axles along with steel dogbones provide strength and durability to keep things running during tough climbs and rough trails.
SPLINED DRIVE SHAFTS
The front and rear drive shafts are splined and sleeved to allow for maximum suspension travel while keeping the power to the wheels.
COILOVER SHOCK ABSORBERS
Even at this small scale, the combination of coilover shocks with simulated reservoirs and durable plastic suspension links delivers the crawling performance you've known and expect from Axial.
FRONT AND REAR SOLID AXLES
The front and rear axles consist of a two piece, molded plastic solid axle design. For optimal handling, the SCX24™ suspension features a three-link front and four-link rear setup.
LED LIGHTS INCLUDED
Two bright LED lights are included and are mounted in the front bumper. An extra LED light port on the ESC allows you to add optional LED lights.
4-LINK REAR SUSPENSION
The suspension geometry utilizes a 4-Link design for the rear which is optimized to reduce axle steer and torque twist. We've also included extra suspension links for adjusting your wheelbase length.
KMC XD229 MACHETE CRAWL WHEELS & NITTO TRAIL GRAPPLER M/T TIRES
Officially licensed KMC XD Machete wheels are legendary in the off-road world. They are molded in black and feature stunning scale details, despite the small scale.
The officially licensed Nitto Trail Grappler M/T Tires offer a fantastic blend of off-road performance while still retaining excellent composure for on-road use.
HINGED BODY SYSTEM
The hinged body system offers easy access to on-board components. You can quickly reach the battery and chassis by removing just two body clips and swinging the body up.
FULL BALL BEARINGS
Just because the SCX24™ is smaller in size doesn't mean the features need to follow suit. No bushings found here, instead the drivetrain is freely spinning on sealed cartridge bearings throughout the entire vehicle.
AXIAL AS-1 SERVO
Mounted just above the front axle is the Axial AS-1 servo, with a servo saver that allows for steering accuracy, while also providing protection for the servo gears in the event of a bind or impact.
Specifications
Color Variant: RED
The SCX24 Deadbolt 4WD is the first Axial off-roader in 1/24 scale. At less than 8" long, it's the perfect rig to take along on outdoor OR indoor adventures - offering factory-assembled ease, scale looks, and confident handling on any trail.
Features
Includes 3 channel radio system, ESC and transmitter batteries
Includes motor and on-board LiPo battery
Realistic narrow-stance rock crawler body in olive green or red
Molded roll cage with realistic light bar
Realistic driver figure and many other scale details
Officially licensed KMC XD229 Machete Crawl wheels
Officially licensed Nitto Trail Grappler M/T tires (S30 compound, large block tread)
Full-time 4WD
Splined and sleeved front and rear drive shafts allow for maximum suspension travel while keeping the power to the wheels
Steel front and rear axles, front stub axles and dogbones provide strength and durability
Rugged steel C-channel frame rails with bracing keep everything rigid and aligned
Front and rear axles consist of a two-piece, molded plastic solid axle design
3-Link front and 4-link rear suspension supply optimal handling
Coil-over shocks with simulated reservoir and durable plastic suspension links deliver proven Axial crawling performance
Front and rear differentials each house a worm gear setup to power the axles and create higher ground clearance. Worm gear drive also provides a low gear ratio to reduce torque twist
Two LEDs in the front bumper for night driving
Needed to Complete
Nothing! Everything you need to begin having fun with your 1/24 scale Deadbolt is included!
What's in the Box?
(1) SCX24™ Deadbolt™ 1/24 Scale 4WD Truck
(1) Axial AE-6 ESC/receiver combo (installed)
(1) Dynamite® 88T brushed electric motor (installed)
(1) Axial AS-1 steering servo (installed)
(1) Axial® AX-4 2.4GHz 3-channel radio
(4) AA transmitter batteries
(1) 350mAh 2S 7.4V LiPo battery
(1) USB LiPo charger
(1) Product Manual
Overview
The SCX24™ Deadbolt™ 4WD is the first Axial® off-roader in 1/24 scale. At less than 8" long, it's the perfect rig to take along on your hiking, camping, and other outdoor and indoor adventures — offering factory-assembled ease, scale looks, and confident handling on any trail.
Even new modelers driving the SCX24 chassis will be well-equipped to tackle tough climbs and rough trails. Like the larger SCX10™ II chassis, this smaller version uses plenty of steel components — from the C-channel frame rails to the front and rear axles and dogbones. Even over off-road, mountainous, rocky and desert terrain, it has the strength to keep pushing onward and upward.
For the most reliable handling, the SCX24 chassis features a three-link front and four-link rear suspension. The combination of coil-over shocks and durable plastic suspension links delivers Axial-worthy crawling performance even at this small scale. The worm gear drive setup permits a high ground clearance plus a low gear ratio that reduces torque twist.
Powered by an included 180-size motor and LiPo battery, the SCX24 Deadbolt shows off competence and charisma on the trails. Check out that Deadbolt body — with its narrow stance, bulging hood, realistic driver figure, and molded roll cage with realistic light bar. The realism continues right down to the ground, where you'll find licensed KMC XD229 Machete Crawl wheels wrapped in Nitto Trail Grappler tires.
Adding even more to its beginner appeal, the SCX24 Deadbolt comes 100% complete and ready to run. Everything required for action is in the box: assembled and finished vehicle; Axial 3-channel 2.4GHz radio system with servo and ESC/receiver unit; Dynamite® 88T brushed electric motor and 350mAh 2S 7.4V LiPo battery; USB LiPo charger; and even four AA cells for the transmitter!
STEEL C-CHANNEL CHASSIS FRAME RAILS
Just like the 1/10th scale SCX10™ II platform, the SCX24™ chassis features rugged and sturdy steel c-channel frame rails with bracing to keep everything intact and aligned.
DYNAMITE® 88T BRUSHED MOTOR
The Dynamite 88T brushed electric motor provides the right amount of torque to help ascend steep climbs. It's mated to a steel motor mount to keep flex to a minimum, which helps protect the gears.
WORM GEARS
The front and rear differentials each house a worm screw and worm gear setup to get the power to the axles and create higher ground clearance.
DURABLE STEEL AXLES
Steel front and rear axles, front stub axles along with steel dogbones provide strength and durability to keep things running during tough climbs and rough trails.
SPLINED DRIVE SHAFTS
The front and rear drive shafts are splined and sleeved to allow for maximum suspension travel while keeping the power to the wheels.
COILOVER SHOCK ABSORBERS
Even at this small scale, the combination of coilover shocks with simulated reservoirs and durable plastic suspension links delivers the crawling performance you've known and expect from Axial.
FRONT AND REAR SOLID AXLES
The front and rear axles consist of a two piece, molded plastic solid axle design. For optimal handling, the SCX24™ suspension features a three-link front and four-link rear setup.
LED LIGHTS INCLUDED
Two bright LED lights are included and are mounted in the front bumper. An extra LED light port on the ESC allows you to add optional LED lights.
4-LINK REAR SUSPENSION
The suspension geometry utilizes a 4-Link design for the rear which is optimized to reduce axle steer and torque twist. We've also included extra suspension links for adjusting your wheelbase length.
KMC XD229 MACHETE CRAWL WHEELS & NITTO TRAIL GRAPPLER M/T TIRES
Officially licensed KMC XD Machete wheels are legendary in the off-road world. They are molded in black and feature stunning scale details, despite the small scale.
The officially licensed Nitto Trail Grappler M/T Tires offer a fantastic blend of off-road performance while still retaining excellent composure for on-road use.
HINGED BODY SYSTEM
The hinged body system offers easy access to on-board components. You can quickly reach the battery and chassis by removing just two body clips and swinging the body up.
FULL BALL BEARINGS
Just because the SCX24™ is smaller in size doesn't mean the features need to follow suit. No bushings found here, instead the drivetrain is freely spinning on sealed cartridge bearings throughout the entire vehicle.
AXIAL AS-1 SERVO
Mounted just above the front axle is the Axial AS-1 servo, with a servo saver that allows for steering accuracy, while also providing protection for the servo gears in the event of a bind or impact.
Specifications
Color Variant: Green
Axial SCX24 drivers looking to add performance, reliability, and increased efficiency to their crawler no longer need to look far to meet those requirements. The Furitek Brushless Motor conversion kit provides you with the necessary components to take your SCX24 (with compatible brushless ESC) to a whole new level of performance.The Komodo brushless 2204 1400kV motor features windings that are built with high quality copper wiring, thin stator laminations, and are precision balanced. These features together deliver high efficiency levels, that is incredibly reliable at all RPM levels. Included with the conversion kit is a aluminum motor mount which supports 2204 outrunner motors, or 2030, 2040, and 2345 inrunner type motors, a 12T brass pinion with 3mm bore, and an aluminum CNC 32T 0.5 Mod spur gear - which is a complete package that can be dropped into your vehicle when paired with a proper brushless ESC.Motor Specifications:kV: 1400No load current: 0.5AWatts: 180Input Voltage: 7.4-14.8V (2-4s LiPo)Resistance: 0.24ohmMax Current: 15ASlots & Pole Count: 12s, 14pMotor Dimensions: 28mm diameter, 19mm height Stator Size: 2204Weight: 29.5g
COMPATIBILITY:
Axial SCX24
The Samix SCX24 Aluminum & Brass 1.0" Beadlock Wheel Set with Scale Hubs is a great way to lower the center of gravity on your micro rig and add an extra touch of detail. The three piece design makes tire mounting easy, and the 7-spoke pattern offers a custom look. Plus, the screw on scale hubs cover up the wheel nuts for improved realism. Package includes four wheels, four wheel nuts and hardware.Features:
Aluminum wheel set with brass rings adds 82 grams
Lower center of gravity for improved performance
Screw on scale hubs for improved realism
Precision machined
Brass outer ring
Fit all tire brands
Silver finish
Compatible with Samix locking hubs (SAMSCX24-6669LH)
COMPATIBILITY:
Axial SCX24
The Samix SCX24 Aluminum & Brass 1.0" Beadlock Wheel Set with Scale Hubs is a great way to lower the center of gravity on your micro rig and add an extra touch of detail. The three piece design makes tire mounting easy, and the 7-spoke pattern offers a custom look. Plus, the screw on scale hubs cover up the wheel nuts for improved realism. Package includes four wheels, four wheel nuts and hardware.Features: Aluminum wheel set with brass rings adds 82 grams Lower center of gravity for improved performanceScrew on scale hubs for improved realismPrecision machined Brass outer ringFit all tire brandsBlack coating to help prevent corrosionCompatible with Samix locking hubs (SAMSCX24-6669LH)
COMPATIBILITY:
Axial SCX24
The Furitek Axial SCX24 Raptor Aluminum Frame Kit adds performance and unique style to your ride! The optional Raptor chassis kit was designed around the Furitek Komodo Brushless Motor, or Furitek Godzilla Motor system. Made with CNC aluminum, these frames come in four different colors to best match your personal style preference.Features:
Precision fit for the Axial SCX24
Manufactured with CNC Aluminum
Designed for Komodo or Godzilla Brushless Motors
COMPATIBILITY:
Axial SCX24
This is a pack of two optional Traxxas Front Heavy Duty Machined Axle Shafts for use with the TRX4 series. These heavy duty axle shafts are used in the front axle only and are machined with the input gear on the shaft. Includes the left and right side.
For the rear, see part# TRA8061
The Samix SCX24 Aluminum & Brass 1.0" Beadlock Wheel Set is a great way to lower the center of gravity on your micro rig. The three piece design makes tire mounting easy, and the 7-spoke pattern offers a custom look. Package includes four wheels and hardware.Features:
Aluminum wheel set with brass rings adds 80 grams
Lower center of gravity for improved performance
Precision machined
Brass outer ring
Fit all tire brands
Silver finish
Compatible with Samix locking hubs (SAMSCX24-6669LH)
COMPATIBILITY:
Axial SCX24
The Hot Racing Axial SCX24 Aluminum Front Axle Case is a machined aluminum front axle housing upgrade for the Axial SCX 24 RTR vehicles. Package includes axle case, worm gear cover and hardware.
Features:
CNC machined billet aluminum axle housing and tubes, anodized black
CNC machined billet aluminum Worm Gear cover, anodized black
Replaces factory plastic axle case housing and diff cover
Direct fit hop up requires no vehicle modification for use
Compatible with Axial SCX24
Replacement for AXI31609
Specifications:
Weight: 12g
Length end-to-end: 65.7mm
Includes:
(1) aluminum axle housing
(1) aluminum Worm Gear cover
COMPATIBILITY:
Axial SCX24
The Samix SCX24 Aluminum 1.0" Wheel Set is a great way to add some bling and some weight to your SCX24. Made from CNC machined aluminum these 1 inch wheels feature chamfered edges and work with standard SCX24 tires. Package includes four black wheels.
COMPATIBILITY:
Axial SCX24
This is a pack of two optional Traxxas Rear Heavy Duty Machined Axle Shafts for use with the TRX4 series. These heavy duty axle shafts are used in the rear axle only and are machined with the input gear on the shaft. Includes the left and right side.
For the front, see part# TRA8062
