This is brand new develop Mini-Z tire call KS Compound, much more grip and long life.
All new KS Compound tire with PNR and KS logo at the sidewall.
All new KS Compound Series
KS1030 Slick Front Tire SUPER SOFT
KS1034 Slick Front Tire SOFT
KS1038 Slick Front Tire MEDIUM
KS1042 Slick Front Tire FIRM
KS2020 Slick Rear Tire SUPER SOFT
KS2024 Slick Rear Tire SOFT
KS2028 Slick Rear Tire MEDIUM
KS2820 Radial Rear Tire SUPER SOFT
KS2824 Radial Rear Tire SOFT
KS2828 Radial Rear Tire MEDIUM
KS4820 14mm Radial Rear Tire SUPER SOFT
KS4824 14mm Radial Rear Tire SOFT
KS4828 14mm Radial Rear Tire MEDIUM
2017 July New HP900 batteries provide high voltage output over timeRecommend charge at 0.7-1.0amp for the best balance between power and run time.Spec:900mah capacityAAA size4pcs
Brand New Low Profile Tires
PN Racing KS & KS-M compounds are our most popular race proven tire compounds
PN Racing KS Compound: its known to offer more grip as the tire heat up and long duration.
PN Racing KS-M Compound: its known to offer quick warm up and good grip from beginning of the race, also suitable for tracks in cold climate.
After months of R&D, we can finally release our brand new low profile high performance tires.
Our new low profile tires are 1.6mm thick, when its installed on the 20mm rims, the diameter will be 23.2mm.
For stock class you don't have to true these tires, it will be broken in after running on RCP track for one battery pack.
For more advanced classes, only the surface (0.1-0.2mm) needs to be trued.
8.5mm tires
KS Compound
KS1130 Slick Front Tire (8.5mm) SUPER SOFT
KS1134 Slick Front Tire (8.5mm) SOFT
KS1138 Slick Front Tire (8.5mm) MEDIUM
KS1142 Slick Front Tire (8.5mm) Hard
2mm Flanged Wheel Lock Nut for Mini-Z AWD & 2WD Drift Chassis such as GLD; DRZ; Drift Art 2 & etc .
Flange Diameter: 5.8mm
Designed to offer larger mounting surface and result in better wheel balance
KSM530 Slick Front Tire (8.5mm) SUPER SOFT
KSM534 Slick Front Tire (8.5mm) SOFT
KSM538 Slick Front Tire (8.5mm) MEDIUM
KSM542 Slick Front Tire (8.5mm) Hard
210BF0:Mini-Z 2WD Machine Cut 10 Spoke Front Wheel F0, F1, OR F2 Black
New design Mini-Z 2WD Wheel with 2pcs in pack.Machine CutMaterial Special ABS plastic.
*MR03 SPORT support this motor with gear ratio not lower than 4.75*
New Version with BALL BEARING
New 2010 Motors Series from 32T to 80T
Spec
- New Brushes and Brushes Holder, timing setting- Balanced armature- New endbell design for increased cooling- Bottom case air cool scoop intake- JAPAN Ball Bearing
Universal Transmitter Steering Wheel Grip
Made by Silicon
OD 46mm
ID 38mm
Height 22mm, Pre-Cutting Line 20mm, 18mm and 16mm.
Fit for 95% transmitter in the market
Color Available: Orange Blue Black and Yellow
Includes:
0.5M regular Pitch Ball Diff with 43T Spur Gear
Spec Data:
Light Weight Alm 7075 Shaft (MR2045UL)
10pcs Ceramic Ball
High quality O-ring, made in Japan
Ball Bearing build in
Ultra V2 0.8mm D-Cut Pressure Plate
New Delrin O-Ring Holder not easy to loss
Gun Metal Color
PN Racing KS & KS-M compounds are our most popular race proven tire compounds
PN Racing KS Compound: its known to offer more grip as the tire heat up and long duration.
PN Racing KS-M Compound: its known to offer quick warm up and good grip from beginning of the race, also suitable for tracks in cold climate.
All new KS-M Compound Series (Comes in green colored bag)
KSM130 Slick Front Tire SUPER SOFT
KSM134 Slick Front Tire SOFT
KSM138 Slick Front Tire MEDIUM
KSM220 Radial Rear Tire SUPER SOFT
KSM224 Radial Rear Tire SOFT
KSM230 Radial Rear Tire MEDIUM
KSM234 Radial Rear Tire Firm
KSM238 Radial Rear Tire Extra Firm
KSM420 14mm Radial Rear Tire SUPER SOFT
KSM424 14mm Radial Rear Tire SOFT
KSM430 14mm Radial Rear Tire MEDIUM
KSM320 Type-F Radial Rear Tire SUPER SOFT
KSM324 Type-F Radial Rear Tire SOFT
KSM330 Type-F Radial Rear Tire MEDIUM
KSM334 Type-F Radial Rear Tire FIRM
KSM338 Type-F Radial Rear Tire EXTRA FIRM
Mounting for Mini-Z MR02 MR03 and PN2.5 chassis
1 x Fiber Glass Front Bumper
1 x Fiber Glass Side Body Post mount plate
4 x Body Post 35mm
4 x Body Clip
4 x M2x4 Countersunk Screws
NEW BLACK VERSION G10 Fiber Glass T-Plate, slightly stiffer than white fiber glass.
SOFT > 2 > 3 > 4 > 5 > HARD
Number 2 Super SOFT
Number 3 SOFT
Number 4 Medium SOFT
Number 5 MEDIUM
Number 6 HARD
High-precision machine cut Black Delrin 64P
Extra length 10.5mm to keep the pinion on the motor shaft
#MR2709 9T
#MR2710 10T
#MR2711 11T
#MR2712 12T
#MR2713 13T
#MR2714 14T
#MR2715 15T
#MR2716 16T
FEATURES:•Unequal length A-Arm suspension for MR-03 chassis.–Modeled after full-scale performance car suspension for realism.–Double A-Arm suspension gives good control of suspension geometry and roll center during travel.–Camber change with suspension compression during cornering keeps wheels near vertical for maximum tire contact with the road. Allows for precise cornering and maximum road holding.•Direct suspension swap–Same width as stock. (MR02/ MR03 PNR2.5W Chassis width)–Ride height remains the same as stock.–0.5mm wider front steering geometry for less offset and faster steering. Overall width still remains the same to fit Auto Scale bodies.•No bump steer throughout suspension travel.•Suspension movement use ball joints instead of sliding knuckles. Eliminates constriction associated with sliding pin especially with high offset wheels.–Low constriction results in consistent cornering.•Machined aluminum ball socket instead of snap-fit. Joints will not pop out even during a hard collision.•Adjustable camber from 0-3° degrees with 1.3°/mm of camber gain.•Adjustable caster from 0-1.8° degrees•4 positions adjustable upper A-Arm pivot–Changes camber gain, static camber and roll center–Quick adjustment with set screw•Includes 3 tie-rods: 0° , +.5° and +1°•Quick down stop adjustment with the turn of a nut•Benefits of the sophisticated suspension system are precise cornering and maximum road holding which adds to mini-z driving pleasure ADJUSTMENT SPEC:Droop AdjustmentCaster AdjustmentCamber Gain and Camber AdjustmentTie Rod Adjustment COMES WITH:1 x Upper Bracket (#MR3062)1 x Lower Carbon Plate Cover (MR3070C)2 x Upper Arm2 x Lower Arm4 x Delrin Balls for Upper Arm and Lower Arm (#MR3080D)2 x Spring Guide Pin (#MR2507)2 x Spring Holder (#MR2056F)1 x Full Option Spring Set (#MR2501C)2 x Knuckle2 x Knuckle Shaft 3mm (#MR3080A3)2 x Knuckle Tie Rod Pin2 x Eccentric Shaft Adjuster (#MR2506)2 x Lower Arm Pin (#MR2509)4 x M2-3mm Set Screw (#MR2510S)1 x 0 Deg Tie Rod (#MR3050G)1 x +0.5 Tie Rod (#MR3050H)1 x +1.0 Tie Rod (#MR3050J)4 x M2-0.2mm Shims (#700501)2 x M3-0.2mm Shims (#700502)2 x M2x3 Countersunk Hex Screw (#709903)2 x M2x4 Countersunk Hex Screw (#709904)4 x M2x6 Countersunk Hex Screw (#709906)4 x M2x6 UFO Head Hex Screw (#708806)2 x M2x10 Countersunk Hex Screw (#709910)REQUIRED PARTS4 x Ball Bearing 3x6x2mm #600126OPTIONAL PARTSMR3080A2MR2506FMR2506FSMR2506FLMR3050TMR3050Q711906
210BF0:Mini-Z 2WD Machine Cut 10 Spoke Front Wheel F0, F1, OR F2 Black
New design Mini-Z 2WD Wheel with 2pcs in pack.Machine CutMaterial Special ABS plastic.
Prefect for SCX24 Stock Battery charging at 0.35A to 0.5A
For Any 2S Lipo batteries with an XH connector (Balance Plug)
This handy charge cable allows you to connect 4mm banana plugs to chargers, and the charger's balance board.
On the battery side, we have provided 3 x XH connectors so that you can charge/discharge up to 3 packs at the same time.
Charge one battery is fine, if you charge 3 batteries together, make sure all batteries are the same type and capacity.Total length 18cm, protected by PE wrapHigh-quality Silicon wire 14AWG for power, 22AWG for Balance Plug
PN RacingThe correct Toe for Kyosho Mini-Z AWD MA020 ONLY!MA0251 Wide -1, Toe OutMA0252 Wide 0MA0253 Wide +1, Toe InMA0254 Narrow -1, Toe OutMA0255 Narrow 0MA0256 Narrow +1, Toe In
PN Racing KS & KS-M compounds are our most popular race proven tire compounds
PN Racing KS Compound: its known to offer more grip as the tire heat up and long duration.
PN Racing KS-M Compound: its known to offer quick warm up and good grip from beginning of the race, also suitable for tracks in cold climate.
After months of R&D, we can finally release our brand new low profile high performance tires.
Our new low profile tires are 1.6mm thick, when its installed on the 20mm rims, the diameter will be 23.2mm.
For stock class you don't have to true these tires, it will be broken in after running on RCP track for one battery pack.
For more advanced classes, only the surface (0.1-0.2mm) needs to be trued.
KS-M Compound
KSM630 Slick Tire (11mm) SUPER SOFT
KSM634 Slick Tire (11mm) SOFT
KSM638 Slick Tire (11mm) MEDIUM
KSM642 Slick Tire (11mm) Hard
Adjustable Ride Height Axle, stock or low down 0.7mm height
Shaft Size 3mm, comes 3mm Wheel Ball Bearing x 4 #600126
Stainless Steel Pin
Delrin Insert
Open Slot for put King Pin Oil
Replaceable Ball Studs (MR3080E)
