Product Overview
The Avid AE B74.2 -2° C Arm Mount is a must-have if you are racing on high bite surfaces such as carpet or turf. This mount frees up the vehicle in the turns and when landing jumps sideways such as corner tabletops. Typically, to get to the low rear toe settings that you need on carpet, you have to start narrowing the pills through the D Mount which is increasing side bite by decreasing your trackwidth. Our C Arm mount prevents that from happening by widening the C pivot block, thus starting you at 1 deg of rear toe with centered pills on the C and D mount instead of 3. You will be amazed at how well your car handles with less rear toe done in the correct fashion.
Details
Removes 2 degrees of rear toe without removing trackwidth.
Frees up the car up in turns and when landing jumps sideways such as corner tabletops.
Made with 7075-T6 and anodized black with silver chamfer highlights.
Laser-etched Avid logo and -2° on the face for easy identification.
Product Overview
Designed to be color coordinated (e.g. Red uses all red wires and sheath) for charging 2S battery packs through 12ga wire. Includes gold-plated 4mm to 5mm bullets on the battery end to cover all battery types and a 4mm bullet on the charging end. Comes with the popular XH 3pin balance plug, which most trim one of the plastic alignment rails with an x-acto to plug right into the charger instead of the balance port. Or you can use the included XH 7pin if you don't want to brave that. Balance leads are 2.5" (63.5mm) longer than the charge leads so they can easily be plugged into any charger design.
Specifications
Color Coordinated (all wires and sheath colors match).
12ga soft silicone wire at 2 feet long (610mm).
Gold-plated bullets, 4mm to 5mm on battery end and 4mm on charger end.
Balance leads are 2.5" (63.5mm) longer than charging leads.
Comes with XH 3pin balance plug installed and includes XH 7pin.
Tips
You can skip using a balance board or changing out to the 7 pin adapter with this simple modification.
Product Overview
The Avid B6.2 Carbon Battery Brace is made from 100% carbon fiber designed for easy plug access. The brace utilizes the stock adjustable battery blocks and comes with (4) SS M3x6 screws and (2) M3 aluminum nuts to secure the battery in place.
Installation
Install with the included M3 nuts on the fixed solid carbon arms towards the front of the car to ensure your battery doesn't shift or break your brace after you drill that steel beam on the triple.
Features
100% Carbon Fiber, 2.5mm thick.
Easy plug access (battery and balancer).
Minimal design weighing in at 6.68g.
Includes (4) SS M3x6 BH Screws, (2) M3 Aluminum Nuts.
Fits: B6.2, B6.2D, B6.1, B6.1D, B6, and B6D.
Product Overview
Our Titanium Lower Shock Mounts for 10th scale vehicles make it easy for getting your shocks off and on while not wearing out the plastic from repeated uses. The one design feature we added to this common product is the 6 small holes in each mount. They are not there to lose weight but rather to help keep the mount from backing out as easily when taking the nut off the end, acting as a bit of a serration.
Features
Machined from billet 6Al-4V Titanium.
6 small holes in each mount to act as a bit of a serration so it will stay in more securely.
Has a 1.5mm Allen head for installation.
No threads where your shock eyelet rests.
Fits common 10th scale vehicles.
Each package includes (2) lower shock mount screws and (2) aluminum M3 flanged locknuts.
Product Overview
The Avid Associated 12mm shock and turnbuckle wrench is a great companion to have in your tool box. The tool offers the ability to adjust Associated, Jconcepts, and Lunsford turnbuckles all in one. It can also be used to hold the shock bottom of a the new Associated 12mm shock, so no need to carry that stamped AE shock tool anymore! But we didn't stop there.
Have you ever had difficulty getting your servo mounted in your B44 because you were trying to make sure that there was no tweak in your mounts when locking it down (servo mount holes perfectly line up when attaching to the chassis)? If so, then problem solved because we added two holes to the tool that mimic the B44 servo mount holes so you can mount your servo up to our tool without being hindered by the gearbox. This allows you to get everything nice and centered. Once you got your Avid Servo Mounts (any servo mount will work though) squared up then detach it from the tool and mount it to your chassis.
Details
Adjust your Team Associated, Jconcepts, and Lunsford turnbuckles all in one tool.
Shock body retainer for 12mm Associated shocks.
B44 servo jig for ensuring your servo doesn't get mounted incorrectly (tweaked).
6061 Aluminum alloy, black anodized with silver edges and laser etched logo.
Each package includes 1 tool and 1 AVID mini decal sheet.
Fits the B5, B5M, B44.2, B4.2, C4.2, T4.2, and SC10.2.
Product Overview
Our popular Avert Aluminum Spring cups for the B6.2 offer you a true rigid surface with the added security that it won’t come off in those demanding conditions. This is accomplished by a unique angled slot design that adds another element of interference to keep the spring cup from popping off. If that wasn't enough, the fit is nice and snug on the shock eyelet to help prevent shock shafts from pulling out of the plastic shock end. The Avert spring cups add that extra security to your ride without sacrificing weight or putting a huge dent in your racing budget.
Features
Fits B6.2, B6.2D, B74, B6, B6D, B5, B5M, B44.3. *Height equivalent to +5 Associated spring cup
Unique angled slot design: Avert Aluminum Spring Cups add 2 elements of safety.
A rigid aluminum spring cup won"t flex and spread open, slipping off of the shock end in a crash.
The angled slot design adds another element of interference to keep the spring cups from popping off in a crash. The spring cup must lift completely off of the eyelet for removal.
Tall inner perch to prevent spring from getting knocked off the spring cup in a crash.
Smooth surface is easy to clean. No nooks and crannys for dirt to get trapped in!
1.3g each. Minimum Weight, Maximum Durability.
6061-T6 Aluminum alloy, black anodized with laser etched logo.
Each package includes 4 spring cups and 1 AVID mini decal sheet.
Product Overview
The Avid Ringer Wing Buttons are designed to have that extra pop of two silver highlights without sacrificing durability.
Details
7075-T6 Aluminum anodized with two silver highlight areas for that extra pop.
M3 flat head screw design to fit nearly every 8th and 10th vehicle on the market.
Available colors: Black, Blue, Red, Pink, Orange, and Silver.
Each package includes 2 Wing Mount Buttons.
Product Overview
Triad Wing Buttons were designed after the success of our other 8th and 10th scale lineup. Coming in at 0.3g each (half the weight of our current 10th button), they are easily the lightest metal button on the market. But we didn't stop there because we dual color anodized them and laser etched our logo to make them even more desirable. When it comes to accessories such as wing buttons and wheel nuts, we know racers like to customize for their personal paint schemes so we are offering these in black/blue, black/gold, black/red, black/pink, black/purple, black/green, black/orange, black, blue, red, green, pink, orange, hard anodize, purple, silver, and gold.
The Triad Wing Buttons are designed for use with an M3 flat head screw which is common on both 8th and 10th scale vehicles.
Details
Aluminum anodized black with gold cut highlights and the Avid logo laser etched.
Minimal weight design, 0.3g/ea with a 16mm OD.
M3 flat head screw design to fit nearly every 8th and 10th vehicle on the market.
Comes in black/blue, black/gold, black/red, black/pink, black/purple, black/green, black/orange, black, blue, red, green, pink, orange, hard anodize, purple, silver, and gold.
Each package includes 2 Wing Mount Buttons, 1 AVID mini decal sheet.
Product Overview
Avid 5.5x8mm Titanium Ball Studs are specially designed for the Team Associated B5, B5M, and SC104x4 to minimize weight without sacrificing strength.
Tips
It is recommended to use all new plastics when switching ball stud brands but isn't necessary. Just be cautious when installing to make sure you don't over tighten them.
Features
Machined from billet 6Al-4V Titanium.
Broached with a 2mm allen head on top of the ball for easy removal.
40% lighter than the kit and optional TiN coated steel ball studs.
Each package includes (2) 5.5x8mm Titanium Ball Studs, and 1 AVID mini decal sheet.
Product Overview
These wire grippers are used to organize your wires going from your speedo to motor but they have endless possibilities.
Details
100% Carbon Fiber, 2.0mm thick.
Fits common 12 and 13awg wire.
Each package includes (2) 3 wire grippers.
Product Overview
B6.2 / B6.2D Carbon Fiber Steering Block Arms (2.5mm) are made from 100% carbon fiber, maintain kit geometry, and saves you a whopping 1g in weight!
Tips
It is recommended to sand the edges and seal the sides with super glue.
When installing, do one screw at a time so that the part doesn't get pinched by the screw threads causing the carbon to split.
Details
100% Carbon Fiber, 2.5mm thick.
Same kit geometry maintained.
Steering Block Weights (2) (Kit: 2.4g | Carbon 1.3g)
Includes (2) Carbon Steering Block Arms, (1) Doodad container, (1) Mini-Decal
Fits: B6.2, B6.2D, B6.1, B6.1D, B6, and B6D.
Product Overview
The Avid (13 - 41 tooth) 48 pitch pinion is made out of 7075-T6 aluminum and hard-anodized to reduce wear and friction. We have laser etched all the details onto the pinion for easy notification. It is the common 1/8" bore (3.17mm) and includes one set screw.
Details
48 Pitch
7075-T6 Hard-Anodized Aluminum
Full range available | 13 - 41 tooth
Laser etched for your convenience
Product Overview
B6.2 / B6.2D Carbon Fiber Steering Block Arms (+2) are made from 100% carbon fiber, increases Ackermann, and saves you a whopping 1g in weight! The +2 increased Ackermann allows the inside wheel to achieve more steering angle than the kit blocks. This reduces scrub and allows the vehicle to rotate better in the middle of the corner. This rotation comes at the price of less steering at the exit of the corner. +1 is in between the kit geometry and our +2 to help you better tune your vehicle, it is suggested that you get our set of all 3.
Tips
Kit Steering Block Arms <---- Less - Middle Steering - More ----> +2 Steering Blocks
It is recommended to sand the edges and seal the sides with super glue.
When installing, do one screw at a time so that the part doesn't get pinched by the screw threads causing the carbon to split.
Details
100% Carbon Fiber, 2.5mm thick.
+2 increased Ackermann for better rotation in the middle of the corner and less exit steering.
A double notch on the side lets you know it is the +2.
Steering Block Weights (2) (Kit: 2.4g | Carbon 1.3g)
Includes (2) Carbon Steering Block Arms, (1) Doodad container, (1) Mini-Decal.
Fits: B6.2, B6.2D, B6.1, B6.1D, B6, and B6D.
Product Overview
B6.2 / B6.2D Carbon Fiber Steering Block Arms (+1) are made from 100% carbon fiber, increases Ackermann, and saves you a whopping 1g in weight! The +1 increased Ackermann allows the inside wheel to achieve more steering angle than the kit blocks. This reduces scrub and allows the vehicle to rotate better in the middle of the corner. This rotation comes at the price of less steering at the exit of the corner. +1 is in between the kit geometry and our +2 to help you better tune your vehicle.
Tips
Kit Steering Block Arms <---- Less - Middle Steering - More ----> +2 Steering Blocks
It is recommended to sand the edges and seal the sides with super glue.
When installing, do one screw at a time so that the part doesn't get pinched by the screw threads causing the carbon to split.
Details
100% Carbon Fiber, 2.5mm thick.
+1 increased Ackermann for better rotation in the middle of the corner and less exit steering.
A single notch on the side lets you know it is the +1.
Steering Block Weights (2) (Kit: 2.4g | Carbon 1.3g)
Includes (2) Carbon Steering Block Arms +1, (1) Doodad container, (1) Mini-Decal.
Fits: B6.2, B6.2D, B6.1, B6.1D, B6, and B6D.
Product Overview
These wire grippers are used to organize your wires going from your speedo to battery but they have endless possibilities.
Details
100% Carbon Fiber, 2.0mm thick.
Fits common 12 and 13awg wire.
Each package includes (2) 2 wire grippers.
