Eliminate the slip. Gain the edge. Upgrade your B6-series buggy with the Factory Team Direct Drive Slipper Eliminator Kit — the precision solution for racers who demand instant throttle response and maximum efficiency. This setup removes the traditional slipper assembly and mounts the spur gear directly to the top shaft, reducing rotating mass by 30% for quicker acceleration and sharper control. Perfect for Stock or Spec class racing (17.5T / 21.5T motors), this kit delivers smoother power transfer and improved consistency on high-traction surfaces like clay or dirt. Key Features: Direct-drive top shaft eliminates the traditional slipper clutch 30% lighter than the stock slipper assembly Faster acceleration from reduced rotating mass Improved drivetrain efficiency may extend run times Ideal for Stock or Spec racing (17.5T / 21.5T) Precision-machined Factory Team quality ⚠️ Note: Not recommended for use on carpet — high-grip surfaces may overstress idler gears. Includes: (1) Top Shaft (Direct Drive) (1) Direct Drive Hub (3) M3x0.5x5mm BHCS Screws (1) M4 Locknut w/Flange Compatible With: RC10 B6.1 / B6.1 Factory Lite / B6.1D RC10 B6.2 / B6.2D RC10 B6.3 / B6.3D RC10 B6.4 / B6.4D RC10 SC6.1 / SC6.2 RC10 T6.2 Team Associated Factory Team – precision, performance, perfection.  

Read more less

Restore precision steering to your B6.4 or B6.4D with this genuine Team Associated replacement set. The kit includes two steering bell cranks and a steering rack, designed to keep your front-end dialed in and race-ready. 🔧 Features: Direct replacement for the RC10B6.4 and B6.4D Includes (2) bell cranks and (1) steering rack Durable, race-proven design ✅ Compatibility: RC10B6.4 RC10B6.4D Ideal for racers who want tight, responsive steering and long-lasting performance.

Read more less

Team Associated RC10B7 Rear Anti-Roll Sway Bars (5) [92458] 🌀 Keep It Tight in the Turns!Fine-tune your cornering performance with the Team Associated RC10B7 Rear Anti-Roll Sway Bar Set. Whether you’re dialing in for grip or freeing up the rear, this 5-pack gives you options to match any track condition. Made specifically for the RC10B7 and B7D platforms, these bars are a must-have in any serious racer’s pit box. 🔧 Key Features:✅ Includes five different sway bar thicknesses🚗 Designed for the RC10B7 and B7D buggies🔄 Helps balance your setup for optimal rear-end control🏁 Swap in and tune for different track surfaces 📦 Includes:(5) Rear Anti-Roll Sway Bars 🔩 Part Number: 92458🛠️ Compatible With: Team Associated RC10 B7 Team Associated RC10 B7D

Read more less

Upgrade your front end with precision, strength, and expanded tuning capability. Weighing just 10.9 grams, this aluminum R1WURKS B7 Front Ball Stud Mount is lighter than the stock plastic piece and adds two in-between ball stud positions for finer camber-link tuning. It also accepts the optional 10g internal weight for racers who want added front-end stability (sold separately). Features Skeletonized design for optimal strength-to-weight balance 0.6g lighter than the stock plastic mount High-strength 7075-T6 aluminum construction Precision CNC-machined for exact fit and alignment Matte black anodized finish with laser-etched R1 branding Two additional in-between camber link mounting holes Compatible with optional 10g internal weight Includes (1) R1WURKS B7 Front Ball Stud Mount, Aluminum Fitment B7 B7D T7 SC7 For best results, apply low-strength blue thread locker to all screws and tighten until snug. Avoid overtightening.

Read more less

JConcepts 12mm Hex Mono 2.2" Front Wheels (4) – Yellow or WhitePart Numbers: JCO3347Y (Yellow), JCO3347W (White) Upgrade your 1/10 buggy with these JConcepts Mono 2.2" Front Wheels, designed for performance, durability, and style. Available in bright white or fluorescent yellow, these wheels feature popular dish-style detailing and are molded using an advanced manufacturing process for maximum precision and strength. Perfect for racers running Team Associated B5, B5M, B4.1, or Kyosho RB5 platforms with 12mm hex conversions, these wheels offer great fitment, longevity, and modern styling. 🔧 Key Features: Fits: Team Associated B4.1/B5/B5M/B4.2 (w/ adaptors), Kyosho RB5 (direct fit) Quantity: 4 wheels per pack Color Options: White (JCO3347W), Yellow (JCO3347Y) ROAR-legal sizing with a dish-style concave design 12mm hex mount Vented design improves glue adherence Made from durable, race-proven material 🛠️ Compatibility Notes: For B4.1: Requires JConcepts clamping hexes (front/rear) and Team Associated hex conversion For Kyosho RB5: Use locking-style rear wheel nuts (JC #2089 Blue or #2090 Black) Designed for standard (wide) front-end configuration Will not work properly with narrow setups or without locking nuts on RB5 Specs: Feature Detail Position Front Diameter 2.2" Hex Size 12mm Quantity 4 Wheels Scale 1/10 Buggy Color Options White / Yellow Vehicle Type 2WD Buggy Bring style and performance to your front end with the JConcepts Mono wheels—perfect for racers who demand precision and durability on the track.

Read more less

  📱 Wireless Tuning. Total Control.Ditch the cords and take full control of your ESC with the Hobbywing OTA Programmer. Designed to work with select Xerun, EzRun, Platinum, and Seaking ESCs, this compact module connects wirelessly to your smartphone using the HW Link App—giving you the power to fine-tune ESC settings, record real-time data, and even update firmware on the go. 🎯 Key Features: Real-time wireless tuning via the HW Link App Graphical interface with drop-downs and sliders for easy setup Built-in data logging and memory storage Seamless Bluetooth transmission One-touch factory reset Compact, lightweight design 📐 Specifications: Voltage: 5–12.6V Bluetooth Version: ≤ 4.0 Range: 0–3m (open field) Size: 30.0 x 25.5 x 8.5mm Weight: 10.2g 💡 Note: Compatible only with supported ESCs. Please check your ESC manual for compatibility. Download the HW Link V2 App for optimal performance. 🎮 Your ESC. Your Way.Whether you're dialing in race settings or checking temps after a bash session, this OTA module makes managing your ESC easier, faster, and smarter.

Read more less

Team Associated RC10B6.2 Rear Suspension Arm, 73mm (91885)Upgrade or replace your buggy's rear end with this 73mm rear suspension arm designed for the RC10B6.2. Engineered for optimal durability and race-ready performance, it's a direct replacement part that keeps your handling sharp and consistent. ✅ Official Replacement – For the RC10B6.2✅ 73mm Length – Ideal for specific tuning setups✅ Durable Composite Material – Built to handle high-impact racing✅ Precision Molded – Ensures consistent fit and suspension geometry 📦 Includes:– (1) Rear Suspension Arm, 73mm Perfect for spares or to replace a worn or damaged arm. Get your buggy dialed in and back on track!

Read more less

Race-proven precision. Built to win.Keep your Team Associated RC10B7 buggy performing at its peak with these genuine Rear Suspension Arms (92408). Engineered for precision geometry and durable flex, they deliver consistent handling and cornering performance on high-grip tracks or rough off-road surfaces. Factory Fit. Track Ready.Molded from high-strength composite material, these arms maintain ideal suspension alignment and reliability through long mains and hard landings. Perfect for racers looking to restore factory feel or fine-tune suspension response on their B7 platform. 💪 Features: Genuine Team Associated factory replacement parts High-strength composite construction for durability and balance Consistent flex characteristics for predictable handling Precision fit for the RC10B7 rear suspension system 📦 Includes: (2) Rear Suspension Arms ✅ Compatibility: Team Associated RC10B7  

Read more less

  Team Associated 3x27.5mm V2 Ti-Nitride Screw Mount Shock Shafts (2pcs) Durability Meets Precision. Upgrade your suspension with Team Associated’s V2 3x27.5mm Ti-Nitride Shock Shafts, engineered for ultra-smooth performance and long-lasting wear resistance. These shafts feature a screw-mount piston design—perfect for racers who demand consistency and reliability lap after lap. Compatible with specific buggy and truck shock bodies, these are a direct fit for serious performance upgrades. 🔩 Features: ✨ Ti-Nitride Coated – Hard coating increases wear resistance and reduces friction 🔧 Screw-Mount Design – Stronger and more secure piston mounting (no E-clips) 🚗 Vehicle Compatibility: Fits ASC91577 Buggy Rear Shock Bodies Fits ASC91578 Truck Front Shock Bodies ⚠️ Note: Not compatible with E-clip style pistons 📦 Includes: (2) 3x27.5mm V2 Ti-Nitride Screw Mount Shock Shafts Trust Team Associated components for reliable performance and race-ready precision.

Read more less

The JConcepts Carpet/Astro High-Clearance 7" Rear Wing is engineered specifically for modern carpet and AstroTurf racing conditions. Featuring a short-chord design for quick rotation and a flat base for increased tire clearance, this wing delivers the balance racers want between downforce and low drag on high-speed layouts. Built from durable material, the wing includes clipped rear corners to improve rigidity and reduce breakage, along with a traditional rear trim-line to fine-tune aerodynamic balance. Large radius cut-outs in the side dams allow for greater rear tire expansion and flex, while dual stability fangs reinforce the structure from front to rear. Maintaining a high-angle vertical rear dam, the HCW provides predictable handling and confidence through fast sections. Multiple cut lines allow racers to customize trim and feel, making this wing one of the most tunable aerodynamic options for 1/10 off-road racing. Features Innovative 7" High-Clearance Wing (HCW) design Short-chord profile for quicker rotation Flat base increases rear tire clearance Clipped rear corners minimize breakage Large side-dam openings for tire expansion and flex Dual stability fangs for added structural strength Pro-level height and rake angle Designed for carpet & AstroTurf racing Compatibility Fits most 1/10 scale off-road buggies Includes (2) JConcepts Carpet/Astro High-Clearance 7" Rear Wings  

Read more less

  Keep your shocks buttery smooth and leak-free with the TLR X-Ring Shock Seal Set. Designed as a direct replacement for all TLR 22, 22T, and 22SCT vehicles, this kit restores proper damping, reduces stiction, and improves long-term shock consistency. Whether you're rebuilding after a long race weekend or refreshing worn seals, these high-quality X-rings and O-rings provide a precise fit and excellent durability. Features Direct replacement for TLR 22 / 22T / 22SCT platforms X-ring seals deliver reduced friction and longer life Helps maintain smooth, consistent shock performance High-quality material resists swelling and leaking Perfect for routine maintenance or full shock rebuilds Includes (8) X-Ring Lower Cartridge Seals (4) Shock Cap O-Rings (4) Lower Cap O-Rings

Read more less

Refresh your suspension performance with the Team Associated B6.1/B6.1D Shock Caps & Spring Cups Set — the exact replacement parts included with the original B6.1 and B6.1D kits. This kit restores smooth, consistent shock action and leak-free performance with all-new caps, spring cups, o-rings, and bleeder screws. Perfect for maintenance, rebuilds, or keeping spares ready in your pit bag. Features Genuine Team Associated replacement parts Includes shock caps, spring cups, o-rings, and bleeder screws Restores smooth shock operation Direct fit with no modifications required Compatible Models RC10B6.1 RC10B6.1 Factory Lite RC10B6.1D RC10B6.2 RC10B6.2D RC10B6.3 RC10B6.3D RC10 B74 RC10 B74.1 RC10 B74.1D RC10 SC6.1 RC10 SC6.2 RC10 T6.2 Includes (4) Shock Caps (4) Spring Cups (4) O-Rings (4) Shock Cap Bleeder Screws

Read more less

🏁 Precision. Strength. Style. The Avid Truss 2.2 Buggy Front Slim Wheels set a new standard for performance and durability in 1/10 buggy racing. Designed for racers who demand precision and style, these wheels feature Avid’s signature concave truss face, optimized rib structure, and lightweight build for superior handling and torque strength. ⚡ Features: 🧱 Truss reinforcement at the hex delivers maximum torque strength and prevents flex under load 💥 Concave vertical face protects axles and wheel nuts from track impacts while giving a premium polished look 🌀 Six internal ribs reduce rotating mass and increase structural rigidity 🧩 Low-profile inner bead ribs let the foam absorb impact for smoother landings 🔩 Reinforced wheel-nut area withstands aggressive serrated nuts ✨ Textured glue bead for stronger tire bonds and cleaner mounting 🌬️ 2.5mm vent holes allow perfect airflow – no drilling needed ⚙️ Standard 2.2” fit for all 1/10 scale buggies 🎨 Available in White or Yellow 📦 Includes: (4) Avid Truss 2.2 Front Slim Wheels 📏 Specifications: Outer Diameter: 2.2” Hex Depth: 2.0mm (Standard Offset) Fitment: 1/10 2WD Buggy Front (Slim Tires) Part Number: AV1112 💡 Pro Tip:Pair these with Avid 2.2 Rear Buggy Wheels and your favorite clay or carpet tires for a perfectly balanced setup that shines on-track and in the pits.    

Read more less

Step up your racing game with these Stiffezel Front Suspension Arms for the TLR 22X! Engineered for high-performance racers, these arms provide increased stiffness and durability to enhance cornering, reduce flex, and maximize your control on high-bite tracks. 🔥 Features: Precision-engineered for the TLR 22X platform Stiffezel material delivers superior rigidity over stock arms Sharper steering response and enhanced high-speed handling Reduced flex = more precise suspension feel Perfect for traction-rich surfaces 📦 Includes:(2) Stiffezel Front Suspension Arms ✅ Compatibility:• TLR 22X• TLR 22X-4• TLR 22X-4 Elite• Losi 22S Sprint  

Read more less

Team Associated RC10B6.2 Factory Team Carbon 75mm Rear Suspension Arms [91874] 💪 Lightweight. 💨 Rigid. 🏁 Race-Proven. Upgrade your RC10B6.2 with the Factory Team Carbon 75mm Rear Suspension Arms—built for racers who demand precision, strength, and speed. Crafted from ultra-rigid carbon material, these arms deliver sharper handling, improved durability, and better stability in high-traction conditions. ✅ 12% lighter than standard "hard" arms✅ Stronger and more durable than previous options✅ Improves high-speed stability and cornering control✅ Ideal for high-traction tracks✅ Direct Factory Team fit and finish Includes:(2) Carbon 75mm Rear Suspension ArmsPlastic Shims 📦 Part Number: 91874🔧 Brand: Team Associated🏎️ Compatible with: RC10B6.2

Read more less

Gens Ace Redline 2.0 2S Shorty LiHV Battery (7.6V/5000mAh) – 140C Burst Unleash the Voltage – Dominate the Track The Gens Ace Redline 2.0 LiHV Shorty Battery is built for serious RC racers looking for explosive acceleration, sustained voltage, and consistent performance. Featuring ultra-low internal resistance and a massive 140C discharge rating, this lightweight pack delivers big power in a compact footprint — perfect for 1/10 scale racing applications. ⚙️ Features: ⚡ 140C Continuous Discharge – massive power for competitive racing 🔋 7.6V 2S LiHV / 5000mAh Capacity – extended runtime with high-voltage punch 🔌 5mm Bullet Connectors – secure, high-amp power delivery 📏 Shorty LCG design – low-profile for improved chassis balance and handling ✅ Factory-matched cells for consistency and efficiency 📐 Specifications: Voltage: 7.6V (2S LiHV) Capacity: 5000mAh Continuous Discharge: 140C Max Charge Rate: 1C (5.3A) Configuration: 2S1P Watt Hours: 38Wh Connector Type: 5mm Bullet Balance Plug: 2mm Bullet Dimensions: 96 x 46 x 19mm Weight: 177g (6.24oz) 🏁 Whether you're battling it out on high-traction carpet or slick dirt tracks, the Gens Ace Redline 2.0 Shorty brings unmatched burst and endurance to your race day setup.

Read more less

  Nitro Pro FK-N500FST – Blazing Speed Meets Precision Control 🏁 Introducing the Nitro Pro FK-N500FST — one of the fastest, strongest, and most advanced servos in the game. Built for racers who need absolute responsiveness without sacrificing power, this servo delivers 500oz of torque at 0.071 transit speed — an elite combo that turns milliseconds into victory. 🔥 With a patented stainless steel gear set, 90 day gear replacement, and a precision-machined billet aluminum case, this servo isn’t just fast — it’s built to outlast the competition. ✨ Key Features: ⚡ 500oz Torque @ 0.071 Transit Speed – Elite-level power and razor-sharp speed🛠️ Patented Stainless Gear Set – Exclusive design for unmatched reliability-100% SATISFACTION GUARANTEE-90 DAY NO HASSLE WARRANTY🏗️ CNC Billet Aluminum Case – Lightweight, heat-resistant, and race-ready💧 IP67 Water Resistant – Track-tested, weather-approved 📦 What’s in the Box? ✔️ (1) Nitro Pro FK-N500FST High-Speed Servo✔️ Peace of mind with lifetime gear coverage Engineered for Champions – Built to Perform Whether you're chasing podiums or pushing limits, the FK-N500FST delivers the strength and speed your build demands. 💡 Dominate the Track – Make the FK-N500FST Your Next Upgrade!

Read more less

Keep your buggy looking sharp and handling at its best!These clear front wings are direct replacements for the RC10B7 and come in the same style as included in the kit. Perfect for having a backup on hand or customizing with your own paint job for that extra flair. ✅ Features: Official Team Associated replacement part Clear polycarbonate – ready for custom paint Matches the original RC10B7 kit wing Adds front-end downforce for better steering feel 📦 Includes: (2) Clear Front Wings for RC10B7 Upgrade, replace, or customize—your RC10B7 deserves the best!

Read more less

Team Associated RC10B6/RC10T6 Factory Team Steel Bulkhead (25°/30°) – 91898Upgrade your rig with this Factory Team Steel Bulkhead! Designed for the RC10B6 and RC10T6 platforms, this optional bulkhead offers two installation angles—25° or 30°—to fine-tune your front-end geometry for sharper steering and better control. 🔧 Features: Factory Team Steel construction for added strength Adjustable geometry: 25° or 30° setup Includes mounting hardware ✅ Compatibility: Team Associated RC10B6 Team Associated RC10T6 Also fits B6.1, B6.2, B6.3 and newer models with compatible front-end setup Perfect for racers looking to dial in precise handling and durability.

Read more less

Team Associated RC10B7 Factory Team Carbon Top Plate & Ballstud Mount Set – Eliminate Flex, Maximize Control! 🏁 Upgrade your chassis stiffness and tuning precision with the Factory Team Carbon Top Plate & Ballstud Mount Set for the RC10B7 and RC10B7D. Constructed from Team Associated’s renowned carbon composite material, this lightweight set reduces unwanted flex on high-bite tracks while improving steering consistency and front-end response. ⚙️ Key Features: ✅ Premium carbon composite construction for lightweight durability✅ Reduces chassis flex for consistent handling on high-traction surfaces✅ Improves steering precision and chassis response✅ Perfect for racers looking to fine-tune front-end stiffness✅ Genuine Team Associated Factory Team option part 📦 Includes: (1) Carbon Top Plate (1) Carbon Ballstud Mount ✅ Compatibility: Team Associated RC10B7 Team Associated RC10B7D 🔥 Dial in your front-end tuning with this high-performance Factory Team upgrade from Team Associated! 🏆🔧

Read more less

1up Racing 7075 LowPro Wing Washers – Lock It Down with Low-Profile Precision 💥 Keep your wing tight and your style tighter with the 1up Racing 7075 LowPro Wing Washers – the go-to choice for elite racers and style-focused builders. Whether you're launching off-road or speeding down the straight, these precision-machined aluminum washers are built to perform and look incredible doing it. 💪 Designed with no cutouts to trap dirt and an oversized 14mm diameter to reduce wing flex, these washers boost rear-end stability and give your ride that unmistakable 1up edge. ✨ Key Features: 🔩 7075 High-Strength Aluminum – Lightweight and tough enough for brutal landings📏 Low-Profile Design – No cutouts = no dirt buildup🌀 14mm Outer Diameter – Minimizes wing flex for consistent aero performance🎨 Available in 10 Anodized Colors – With mirror-like chamfered edges for that clean, pro look💡 Drag Car Ready – Clean body mount solution with aerodynamic benefit 📦 What’s Included? ✔️ (2) 7075 LowPro Wing Washers in your chosen color Note: Use with standard M3 flat head screws (not included). Slight screw head protrusion helps preserve the anodized finish. 🏁 Stay Locked. Stay Clean. Stay Fast. Whether you're racing, bashing, or building to win, the 1up Racing LowPro Wing Washers deliver race-ready function and next-level style. 💡 Finish Your Build Right – Add 1up Wing Washers to Your Setup Today!

Read more less

Dial in your aero and add a clean, pro finish to your 1/10 RC build with BOOF RC Wing Washers.These lightweight aluminum washers reinforce your wing mounting points, preventing cracks, pull-through, and premature wear — especially on high-downforce setups. Designed for racers who want performance, durability, and style without paying premium brand prices. Features: ✔️ Lightweight Aluminum Construction – Strong and low-mass for optimal wing support ✔️ Reduces Wing Damage – Prevents cracking and screw pull-through ✔️ CNC Machined Finish – Clean fitment with a premium look ✔️ Multiple Color Options – Customize your style ✔️ Easy Bolt-On Upgrade – Works with standard 1/10 wing hardware Specs: Fitment: 1/10 RC (buggy, touring, drift, basher) Material: Aluminum Hardware: M3 mounting compatible Pack: 2pcs (one pair) Available Colors: 🟥 Red⬛ Black🩶 Titanium🟦 Royal Blue🩵 Light Blue 🟩 Green🟪 Purple⭐ Gold🤍 Silver (Availability may vary) In the Pack: (2) BOOF RC Aluminum Wing Washers Perfect For: 1/10 Buggies 1/10 Touring & Drift High-downforce setups Bashers that break wings often Why BOOF RC? Affordable, clean, functional upgrades — without the silly markup.  

Read more less

Dial in elite front-end steering and precision with the JConcepts Pin Swag LP Wide 2.2" Front Carpet Tires — engineered for today’s high-grip carpet racing where responsiveness, consistency, and low-rolling resistance matter most. Designed for 2WD front buggies, the Pin Swag blends the proven outer lug profile of the Swagger with a dense cluster of micro pins for unreal grip and smooth, predictable steering. The wide, low-profile carcass offers a larger contact patch and flatter feel, helping your buggy stay aggressive without getting twitchy. Hybrid Pin + Swag Traction The design combines: Outer Swag lugs for crisp steering bite Tightly packed round pins for smooth forward grip and minimized wear A split center section that flexes naturally for carpet surface compliance Together, they deliver a fast, confident front-end feel that works across layouts — technical, high speed, or tight and grippy. Engineered for Carpet Performance Built on the same low-profile concept that made the Fuzz Bites so successful, the Pin Swag rolls through corners with ease. A vertical rib paired with a staggered inside section adds stability on corner entry, while the directional layout provides consistent steering through the full rotation. The scalloped tire beads remove unnecessary weight, reducing rotational mass and helping your buggy accelerate and rotate quicker through the infield. Features JConcepts original hybrid Pin + Swag lug design Low-profile, wide-body carcass for increased front contact patch Crisp-tipped round pins for maximum bite Durable, dense pin layout to minimize wear Smooth Swag transition near the sidewall for predictable cornering Ultra-light scalloped beads for reduced rotating mass Compatible with all standard 2.2” 2WD front buggy wheels Includes (2) Pin Swag LP Wide 2.2" 2WD Front Buggy Tires (Pink Compound) (2) Low-profile scalloped foam inserts  

Read more less

Upgrade your suspension precision with the Factory Team 13mm Shock Pistons from Team Associated. The #91932 piston set features two 1.6mm holes with a 2.5mm thickness, providing a stiffer pack than larger hole configurations—ideal for high-speed, high-traction conditions. 📦 Includes: (2) FT 13mm Shock Pistons – 2x1.6mm holes 2.5mm thick profile ⚙️ Key Features: Designed for 13mm shock bodies Precision-molded for consistency and smooth operation Offers increased damping over 2x1.7 and 2x1.8 setups Used by top racers for fine-tuning on rough or fast tracks Fits platforms like RC10B6.4, RC10B74.2, and more 📌 Tuning Note: Smaller holes = more pack. Great for front shocks when you want the car to stay flatter in transitions or landings.

Read more less

FlySky Noble NB4 Pro+ AFHDS3 18-Channel 2.4GHz Radio System w/ FGr4B & FGr8B Receivers 🔥 The Ultimate Transmitter for Champions! 🚗💨 The FlySky Noble NB4 Pro+ AFHDS3 18-Channel 2.4GHz Radio System is designed with elite RC racers and enthusiasts in mind. Packed with advanced technology, a high-resolution color touchscreen, and ultra-low latency response, this radio system delivers unmatched control, precision, and reliability. Whether you're racing, crawling, bashing, or flying, the NB4 Pro+ is the top choice of world champions! 🏆 With 18 programmable channels, a powerful 3450mAh battery for extended runtime, real-time telemetry monitoring, and USB Type-C connectivity, this system provides next-level customization, performance, and durability. The included FGr4B (4-channel) and FGr8B (8-channel) receivers ensure rock-solid signal stability with AFHDS3 digital frequency-hopping technology. ✨ Key Features: 🎮 18-Channel Support – Provides extensive control customization for multiple applications 🖥️ 3.5" Full-Dot Matrix Color Touchscreen – High-resolution 320x480 display for intuitive navigation ☀️ IPS High-Brightness Display – Designed for clear visibility even in direct sunlight 🎨 Customizable UI & Themes – Personalize the interface with custom wallpapers and channel names 🔌 USB Type-C Port – Supports coach mode, head tracking, and firmware updates 🔋 3450mAh Quick-Release Battery – Up to 18 hours of runtime with included power base 💾 Model Memory & Telemetry Support – Monitor real-time battery voltage, temperature, and signal strength 🔄 Adjustable & Detachable Steering Wheel – Configurable for left- or right-handed users 🏎️ Ultra-Low Latency 2CH Mode – Ensures instant response times for high-speed racing 📡 AFHDS3 Protocol – Automatic frequency-hopping technology eliminates interference 🚀 Ergonomic, Lightweight Design – Comfortable grip for extended use 🎒 Premium Carbon Fiber Carrying Case Included – Protects your radio system in style 📦 What’s in the Box? (1) FlySky Noble NB4 Pro+ AFHDS3 18-Channel 2.4GHz Radio System (1) FGr4B 2.4GHz 4-Channel AFHDS3 Receiver (1) FGr8B 2.4GHz 8-Channel AFHDS3 Receiver (1) 3450mAh 18650 Battery (1) Hard Carrying Case with Carbon Fiber Finish (1) FlySky Lanyard (1) Decal Sheet 📖 Product Manual 📌 Note: Everything needed is included—no additional accessories required! 📊 Specifications: Input Voltage: 1S LiPo / 3450mAh 18650 Battery Protocol: AFHDS3 Frequency: 2.4GHz RF Range: >300m Channels: 18 Dimensions (L x W x H): 5.62 x 4.72 x 9.13 in (142.7 x 120 x 232mm) Weight: 23.63 oz (670g) 🏁 Experience Unmatched Control & Performance! 🔥 Whether you're a competitive racer, rock crawler, or RC aviation enthusiast, the FlySky Noble NB4 Pro+ delivers next-generation precision, customization, and responsiveness. 💨 Upgrade today and take your RC experience to championship levels! 🏆🏁

Read more less

Team Associated RC10B6.2 Rear Suspension Arm, 73mm   ASC91853

Read more less

Team Associated B6 Laydown Idler Gear (39T) (91716)Keep your laydown transmission running smooth with these genuine Team Associated 39T idler gears. Designed for the RC10 B6, B6.1, and B6.2 series buggies with a laydown setup, these are the direct replacements you need for peak drivetrain performance. Includes: (2) 39T Idler Gears Compatibility: RC10 B6 RC10 B6.1 RC10 B6.2 (with laydown transmission)

Read more less

Team Associated RC10B7 Front Anti-Roll Sway Bars (5) [92459] 🌀 Precision in the Front, Grip in the Back!Upgrade your front-end handling with the Team Associated RC10B7 Front Anti-Roll Sway Bar Set. Whether you're fighting traction roll or just fine-tuning your buggy for max consistency, this 5-pack of sway bars gives you the tuning range you need to dominate any surface. Built for the RC10B7 and B7D platforms—just swap, test, and race! 🔧 Key Features:✅ Five sway bar options for ultimate front-end tuning🔄 Designed specifically for RC10B7 and B7D🎯 Helps maintain front grip and stability through corners🏁 Race-proven setup flexibility 📦 Includes:(5) Front Anti-Roll Sway Bars 🔩 Part Number: 92459🛠️ Compatible With: Team Associated RC10 B7 Team Associated RC10 B7D

Read more less

1up Racing Lockdown Adjustable Bullet Plugs – Tool-Free Power, Trackside Ready 🔧 Say goodbye to wobbly connections and clunky installs — the Lockdown Bullet Plugs by 1up Racing are here to redefine how you power your RC car. These are the world’s first fully tool-free adjustable bullet plugs, delivering max efficiency, minimal resistance, and an unbeatable fit — all with just a twist. 💡 With an innovative compression-fit system and eye-catching finishes, these aren’t just bullet plugs — they’re an upgrade in performance and style. ✨ Key Features: 🔧 Tool-Free Adjustable Design – Get a perfect fit in 5mm or 4mm sockets without a single tool⚡ Low Resistance, High Efficiency – Maximize power transfer from battery to ESC🌀 Easy-Grip Thumb Screws – Fast install, secure lock-in every time📏 Ultra-Low Profile – Only 8mm tall when installed (shorter than 1up Heatsink Bullets)🖤 Dual-Tone Style – 10 bold anodized colors for the positive plug, with a sleek black negative🌟 Mirror-Like Chamfer & Deep Laser Engraving – Looks as good as it performs💪 Lightweight & Durable – Built for serious racers who demand reliability 📦 What’s in the Box? ✔️ (2) Lockdown Adjustable Bullet Plugs (1x Positive Color, 1x Black Negative) 📌 Note: Installed height may vary slightly depending on your battery terminal’s snugness. Looser terminals = lower thumb screw depth. 🏁 Don’t Get Caught Slippin’ – Lock In with 1up! When every millisecond counts, 1up Racing’s Lockdown Bullet Plugs deliver unmatched grip, power, and pit-lane convenience. No tools, no fuss — just pro-grade power transfer and personalized style. 💡 Upgrade to Lockdown Plugs – Because “Good Enough” Ain’t Fast Enough.

Read more less

🧵🔧 Clean Mounting. Strong Hold. Easy Access. The ProTek RC Body Mounting Hook & Loop Tape provides a simple, reliable solution for securing RC bodies and accessories. With a full 1-meter length, you can cut exactly what you need for a clean, custom setup. 🏁 About This Tape ✂️ Fully Customizable Supplied in a 1-meter length, this tape can be cut to fit any application—from body mounting to accessory placement. 🔒 Secure & Reliable Hold The hook and loop design keeps bodies and components firmly in place, even under demanding conditions. 🔄 Quick Removal Easily remove your body for maintenance or battery changes without dealing with clips or hardware. 🔧 Key Features ✔ 1-meter length for custom applications✔ Strong hook & loop fastening system✔ Secure hold for RC bodies and accessories✔ Allows quick and easy removal✔ Ideal for clean, clipless setups✔ Versatile for multiple RC uses 📦 Includes (1) Hook & Loop Tape (1 Meter Length) 🧰 Recommended Use Body mounting (clipless setups) Securing electronics or accessories Custom RC builds and modifications    

Read more less

The R1WURKS Slipper Eliminator Gear is a precision-machined 48-pitch spur gear designed specifically for use with slipper eliminator hubs. Made from POM (Polyoxymethylene), this gear delivers low friction, excellent wear resistance, and consistent performance—ideal for stock racers running a locked-out drivetrain. Featuring a standard inner bore and bolt pattern, this gear fits most slipper eliminator hubs, including the R1WURKS B7 hub. Features & Specifications 48-Pitch spur gear Precision machined for accuracy and concentricity Made from POM (Polyoxymethylene) Low friction High durability Excellent wear resistance Standard inner bore and bolt pattern Designed for slipper eliminator setups Options 69 Tooth – 900055-69 72 Tooth – 900055-72 Includes (1) Precision machined slipper eliminator gear(Select desired tooth count) Fitment Team Associated RC10 B7 fitted with R1WURKS 900054-1 B7 Slipper Eliminator Hub or similar aftermarket hub Team Associated RC10 B7D fitted with R1WURKS 900054-1 B7 Slipper Eliminator Hub or similar aftermarket hub A lightweight, durable spur gear built for racers running slipper eliminators who want smooth power transfer and long service life. 🏁

Read more less

  Give your brushless system the reliability and protection it deserves with the ProTek RC Braided Sensor Cable. Designed for high-performance RC setups, this premium cable ensures smooth, accurate communication between your ESC and motor — even in the most demanding conditions. Overview The ProTek RC braided sensor cable features flexible silicone-insulated internal wires protected by a rugged black nylon braided sheath. Heat-shrink reinforcement on both ends secures the braid, prevents wear, and keeps the harness stable through constant chassis flex and vibration. The result is a durable, smooth-bending sensor cable that maintains consistent signal integrity for peak motor performance. Compatible with any sensor-based brushless motor system that uses a standard replaceable 6-wire sensor harness. Features Tough nylon braided outer sheath for maximum protection Silicone-shielded internal wires Heat-shrink reinforced ends Flexible, shock-absorbing design Maintains clean and stable ESC–motor data transfer Compatible with all standard 6-wire brushless systems Ideal for racing or high-performance applications Includes (1) ProTek RC Braided Brushless Motor Sensor Cable — 200mm  

Read more less

Upgrade your brushless setup with the ProTek RC Braided Sensor Cable — built for durability, flexibility, and ultra-reliable data transfer between your ESC and motor. Whether you're racing or bashing, this premium sensor cable ensures clean communication and long-lasting performance. Overview The ProTek RC braided sensor cable uses flexible silicone-shielded internal wires wrapped in a tough nylon braided outer sheath for maximum protection. Heat-shrink ends secure the braid and reinforce the connection points, preventing damage or fraying. This creates a smooth-bending, shock-absorbing cable that maintains consistent sensor accuracy under extreme chassis movement. Perfect for any sensor-based brushless system that uses standard replaceable sensor harnesses. Features Durable black braided nylon outer sheath Silicone-shielded internal sensor wires Heat-shrink reinforced ends for long life Flexible, shock-absorbing design Ensures clean and consistent ESC–motor data transfer Compatible with all standard brushless systems using 6-wire sensor leads Great upgrade for racing applications Includes (1) ProTek RC Braided Brushless Motor Sensor Cable — 150mm

Read more less

The Triad Direct Drive System is designed for stock-class racers looking to eliminate the slipper clutch and reduce rotating mass for maximum efficiency. By removing the entire clutch assembly, this system delivers zero slip (other than the differential) and a more direct throttle feel in conditions where ultimate drivetrain efficiency matters. This is the lightest direct drive system on the market, weighing 6.45g with a 72T spur and just 2.62g without a spur. ⚠️ Note: Spur gear is NOT included. This option is intended for racers who already own Triad spur gears. Product Details Direct drive system for stock-class racing Eliminates slipper clutch and rotating mass Zero slip drivetrain (except differential) Lightest direct drive system available All-aluminum construction No small screws to lose during maintenance Custom M3x48 aluminum screw allows clean install and easy return to a slipper setup if desired Works exclusively with Triad spur gears (spur not included) Includes Direct Drive aluminum plate M3x48 aluminum screw Aluminum hat bushing Aluminum cone washer M3 aluminum nut Fitment Team Associated B7 Important Notes Not recommended for all drivers Best suited for experienced stock racers Install is the same as B6.1 (reference Triad Direct Drive assembly instructions) A purpose-built option for racers chasing every gram and every advantage. 🏁 💡 Pro Tip: Direct drive setups aren’t for everyone — but on stock classes and high-grip tracks, removing the slipper can give you a noticeable edge in efficiency and throttle response.  

Read more less

  Achieve pro-level setup accuracy with the JConcepts Aluminum Ride Height Gauge. Machined from billet aluminum, this high-spec tool provides precise measurements from 10–40mm, making it a must-have for competitive off-road racers. With laser-etched markings, smooth pivoting action, and a secure thumbscrew lock, this gauge ensures your ride height adjustments are consistent and repeatable. 🔥 Key Features: Precision-machined from billet aluminum Available in Blue (JCO2282-1) or Black (JCO2282-2) anodizing Laser-etched graduated scale from 10mm–40mm Rounded boss touch point for accurate chassis contact Chamfered silver edging highlights the design Pre-assembled with 4mm pivot hardware & 3mm thumbscrew Includes a latched storage box with foam insert for protection ✅ Compatibility: Works with a wide variety of 1/10 and 1/8 scale on-road and off-road vehicles Ideal for buggies, trucks, and touring cars (TC6/TC7 series) Suitable for any chassis requiring precise ride height adjustments within 10–40mm 📦 Includes: (1) JConcepts Ride Height Gauge (choose Blue or Black) (1) Latched Storage Box with Foam Cushion ⚠️ Tip:Most racers prefer to set ride height with a slight gap (~0.5mm) between the chassis and gauge for best performance.

Read more less

Fine-tune the rear suspension of your RC10B6.3 with the Wide “C” Arm Mount from Team Associated. Made from high-quality aluminum for added strength and precision, this Factory Team upgrade delivers improved durability and consistent geometry for high-performance setups. 🔥 Key Features: Factory Team aluminum arm mount for increased rigidity Wide “C” mount geometry for specific rear pivot configurations CNC-machined for precise fit and performance Hard-anodized finish for wear resistance and professional look Perfect for racers needing a durable, race-ready upgrade ✅ Compatibility: RC10B6.3 RC10B6.3D Also fits other RC10B6-series vehicles using the wide C arm mount configuration 📦 Includes: (1) Aluminum Arm Mount C (Wide) ⚠️ Tip:Pair with the correct A/B/D mounts to achieve your desired anti-squat and toe-in settings.

Read more less