Team Associated Rear Suspension Arms, Hard: RC10B74   ASC92131

Read more less

Team Associated RC10B74.2 FT 2-Gear Differential Cross Pin Set – ASC92322 Upgrade Your Diff for Maximum Durability. Designed for racers using the two-gear differential configuration, the Factory Team 2-Gear Cross Pin Set includes two solid steel pins built to handle high loads and increase longevity. A must-have for optimizing the performance and reliability of your RC10B74 series buggy. 🔧 Features: ✅ Designed for 2-gear diff setups ✅ Solid steel construction for enhanced strength ✅ Factory Team precision for top-tier durability ✅ Ideal for racers seeking reduced rotating mass 📦 Includes: (2) Solid Steel Cross Pins ✅ Compatibility: RC10B74 RC10B74.1 / B74.1D RC10B74.2 / B74.2D 🏁 Trusted by top drivers—reinforce your differential with this Factory Team upgrade!

Read more less

Gens Ace Redline 2.0 2S Shorty LiHV Battery (7.6V/6000mAh) – 140C Burst Race-Ready Power. Expanded Runtime. Shorty Format. Push your limits with the Gens Ace Redline 2.0 6000mAh LiHV Shorty — a premium high-discharge racing battery built for domination. Engineered with Silicon Graphene technology, this pack delivers stable voltage, a flatter discharge curve, and long-term cycle performance — all in a low-profile shorty size perfect for 1/10 scale competitive setups. ⚙️ Features: ⚡ 140C Continuous Discharge – massive power delivery for serious racers 🔋 7.6V LiHV / 6000mAh Capacity – extended runtime and high-voltage performance 🔌 5mm Bullet Connectors – high-amp, secure connectivity 🪶 Shorty LCG Design – optimized for low center of gravity setups 🔬 Factory-matched cells for superior balance and reliability 📐 Specifications: Voltage: 7.6V (2S LiHV) Capacity: 6000mAh Continuous Discharge: 140C Configuration: 2S2P Watt Hours: 45.6Wh Connector: 5mm Bullet Balance Plug: 2mm Bullet Dimensions: 96 x 47 x 25mm Weight: 220g (7.76oz) 🏁 For racers needing a perfect blend of raw power, extended runtime, and reliable heat management, the Gens Ace Redline 2.0 6000mAh Shorty delivers. Built for the podium.

Read more less

1up Racing LowPro 5mm Bullet Plugs – Ultra-Low Resistance, Pro-Level Finish ⚡ Dial in your wiring setup with 1up Racing LowPro 5mm Bullet Plugs — engineered for elite-level performance and clean installs. These compact, low-profile plugs feature an oversized 6-point contact for rock-solid connections and ultra-low resistance, maximizing efficiency and power delivery. 💡 Designed with a deep solder recess and only 15mm total length, these plugs are ideal for tight spaces and lightweight builds. Perfect for all LiPo batteries with 5mm inputs. ✨ Key Features: 🔩 LowPro Design – Just 15mm long for reduced weight and a cleaner install⚡ Oversized 6-Point Contact – Ensures secure fit and minimal resistance🔥 Easy-Solder Recess – Create strong, clean solder joints with 11–16 gauge wire📦 Universal Fit – Compatible with all LiPo packs using 5mm bullet connectors🛠️ Lightweight & Efficient – Built for performance and durability 📦 What’s in the Box? ✔️ (2) 1up Racing LowPro 5mm Bullet Plugs 💡 Upgrade Your Wiring Game – Get 1up Racing LowPro Bullet Plugs Today!

Read more less

1up Racing UltraLite 30mm High-Speed Aluminum Fan w/ Guard – The Coolest Way to Stay Cool! Keep your electronics running at peak performance with the 1up Racing UltraLite 30mm High-Speed Aluminum Fan, featuring an integrated guard for maximum protection, ultra-lightweight design, and high-speed cooling. Engineered for both hardcore racers and weekend enthusiasts, this 10g fan provides exceptional airflow while keeping weight to a minimum. Key Features: ✅ Ultra-Lightweight Design (Only 10g!) – Reduces weight without sacrificing cooling performance.✅ Integrated Aluminum Guard – Protects fan blades from debris and allows for shorter mounting screws, saving even more weight.✅ High-Speed Dual Ball Bearings – Ensures smooth, long-lasting performance.✅ Powerful Airflow – Spins at 29,000 RPM @ 8.4V for maximum cooling efficiency.✅ Short 30mm Cable with 2-Pin Connector – Works with many ESCs for easy plug-and-play installation.✅ Includes 200mm JR Extension Cable – Allows you to connect to a receiver or hard-wire the fan.✅ Versatile Mounting Options – Includes 4x M2.5x6mm screws & 4x M3x6mm screws for secure installation. Precision Cooling for Serious Racers! 🏁 Designed for High-Performance RC Vehicles: Mounts easily with standard 30mm fan spacing (24mm holes). Compatible with 6.0V – 8.4V input voltage. Pair with the 1up Racing Brass Chassis Mount for a low center of gravity and secure chassis mounting. 🔥 Keep your electronics cool and your performance hot with the 1up Racing UltraLite 30mm Fan! Specifications: Input Voltage: 6.0V – 8.4V Outer Dimensions: 12 x 30 x 30mm Mounting Hole Spacing: 24mm (Standard for 30mm Fans) Weight: 10.0g Connector: Basic 2-Pin with 200mm JR Extension Bearings: Dual Ball Bearings Fan Blades: 5 Max RPM: 29,000 @ 8.4V In the Box: (1) 1up Racing UltraLite 30mm High-Speed Aluminum Fan w/ Guard (1) 200mm JR Extension Cable (4) M2.5x6mm Screws (4) M3x6mm Screws Stay Cool & Race Faster! Designed for performance-driven racers, the 1up Racing UltraLite 30mm High-Speed Aluminum Fan offers industry-leading cooling power, ultra-lightweight design, and unmatched durability. 🔥 Upgrade today and keep your RC electronics running cooler than ever! 🏁💨

Read more less

Keep your drivetrain running smooth and protected with R1WURKS Black WS2 Grease. Specially formulated for high-performance RC applications, this grease is ideal for universal joints, dogbones, drive cups, and other high-load drivetrain components where reduced friction and long-lasting lubrication are critical. Infused with WS2 (Tungsten Disulfide) particles, this grease provides exceptional lubrication under extreme pressure while maintaining smooth performance even at elevated temperatures. ⚙️ High-Performance Drivetrain Lubrication The WS2 formula offers an extremely low coefficient of friction, helping drivetrain components operate more efficiently while reducing wear. With an impressive 300,000 PSI load-bearing capacity, it is designed to handle the heavy loads and impacts commonly experienced in RC racing and bashing. 🔧 Built for Extreme Conditions R1WURKS Black WS2 Grease is engineered to remain stable even in harsh environments. Its high dropping point allows it to stay fluid at high temperatures, preventing the grease from breaking down or solidifying during demanding runs. It also provides strong resistance against water, rust, and humidity, helping protect components from corrosion and long-term wear. ⚡ Features Designed for RC drivetrain components Ideal for dogbones, drive cups, and universal joints WS2 (Tungsten Disulfide) lubrication technology Extremely low coefficient of friction 300,000 PSI load-bearing capacity Excellent resistance to water, rust, and humidity High-temperature stability Resists abrasion and extreme pressure 📦 Includes (1) 3g Tube of R1WURKS Black WS2 Grease A must-have maintenance product for racers and builders looking to reduce drivetrain friction, protect components, and maintain peak performance.  

Read more less

Upgrade your RC10B6.3 front-end handling with these Factory Team Steering BlockArms. Featuring a +1mm height and made from lightweight carbon fiber, these HT (High Traction) arms are designed to optimize steering feel and response in high-grip conditions. A must-have for racers looking to fine-tune their setup for maximum performance. 🔥 Key Features: Genuine Team Associated Factory Team upgrade +1mm height for increased front roll center High traction (HT) geometry improves cornering in grippy conditions Constructed from precision-cut carbon fiber Lightweight and durable for competition use ✅ Compatibility: RC10B6.3 RC10B6.3D May fit other RC10B6-series vehicles with similar front-end geometry 📦 Includes: (1) Left Steering Block Arm (1) Right Steering Block Arm ⚠️ Note:Factory Team parts are intended for experienced builders and racers. Always check fitment before installation.

Read more less

Dial in your suspension for ultimate precision with the Factory Team 13mm Shock Pistons. The #91931 pistons feature two 1.5mm holes, offering maximum damping for high-traction surfaces and rough tracks where control is key. 📦 Includes: (2) FT 13mm Shock Pistons – 2x1.5mm hole configuration 2.5mm thickness ⚙️ Key Features: Compatible with 13mm Team Associated shock bodies CNC-precision molding ensures consistency Smaller hole size for slower rebound and increased pack Ideal for high-bite or rough surface tracks Tuning option for front or rear shocks on RC10B6.4, RC10B74.  

Read more less

Upgrade your drivetrain with this optional set of TLR 22X-4 68mm CVA Driveshaft Bones. Precision-engineered for the front/center position, these driveshafts deliver smoother power transfer, improved durability, and consistent performance lap after lap—perfect for serious racers looking for reliability and precision. 🔧 Features:✅ 68mm CVA driveshaft bones for front/center position✅ Designed for optimized durability and power delivery✅ Precision machined for smooth, consistent operation✅ Ideal for high-performance race setups 📦 Includes:• (2) 68mm CVA Driveshaft Bones 🚗 Compatibility:• Losi 22S Sprint• Losi 22X• Losi 22X-4• Losi 22X-4 Elite Dominate the track with smoother handling and added strength—this is a must-have upgrade for your Losi race platform!

Read more less

Team Losi Racing Upper Shock Bushing Set (4) – TLR5092 This is a genuine Team Losi Racing Upper Shock Bushing Set, designed for the TLR 22 1/10 buggy. These bushings provide a secure, smooth mounting point for your shock assembly and help reduce unwanted flex or wear during aggressive driving. ✅ Includes: 4 upper shock bushings✅ Fits: TLR 22 series✅ Genuine TLR performance parts Keep your suspension smooth and race-ready with factory-spec replacement bushings.

Read more less

Team Associated 13mm Front Shock Spring. These optional springs are intended for the Team Associated B6.4D and the B6.4. Package includes two springs. Effects of Shock Spring Changes  Shock Spring  Characteristic  Softer Increased Chassis Roll Increased Traction Better in Bumpy Conditions More Likely to Bottom Out  Stiffer Decreased Chassis Roll Decreased Traction Increased Responsiveness COMPATIBILITY: Team Associated RC10 B74.2Team Associated RC10 B74.2DTeam Associated RC10B6.4Team Associated RC10B6.4D

Read more less

Team Associated Rear Suspension Arms: RC10B74   ASC92130

Read more less

Team Associated RC10B74.1 Anti-Roll Bar Set (1.4–1.7mm) – 92290📏 Dial In Your Roll Game! Fine-tune your handling like a pro with this optional anti-roll bar set for your RC10B74.1 or B74.1D. Whether you're dialing in for high-bite tracks or looking for more stability in the corners, this set gives you the range you need to dominate. 💪 Key Benefits:✅ Includes 1.4, 1.5, 1.6, and 1.7mm sway bars✅ Smoother cornering and better chassis balance✅ Essential tuning option for competitive 4WD racers✅ Designed to fit the RC10B74.1 and B74.1D platforms 🔧 Includes:• (1) 1.4mm Sway Bar• (1) 1.5mm Sway Bar• (1) 1.6mm Sway Bar• (1) 1.7mm Sway Bar 📦 Part Number: 92290🏁 Brand: Team Associated  

Read more less

Team Associated RC10B74.2 Front Gullwing Suspension Arms. This is a replacement intended for the RC10B74.2 and B74.2D series of vehicles. Package includes one left front gullwing suspension arm, one right front gullwing suspension arm and two arm spacers. COMPATIBILITY: Team Associated RC10 B74.2Team Associated RC10 B74.2D

Read more less

Team Associated Rear CVA Axle – 66mm (RC10B74) Restore or upgrade your B74 drivetrain. The ASC92207 66mm Rear CVA Axle is a precision-engineered replacement part designed specifically for the Team Associated RC10B74. Whether you're maintaining performance or rebuilding after wear, this axle ensures smooth power delivery and durability for competitive 1/10 4WD off-road racing. ⚙️ Features: 🛞 66mm length optimized for rear CVA driveshaft assemblies 🧰 Direct replacement for factory parts 💪 Hardened for strength and longevity under racing conditions 📦 Includes: (1) 66mm Rear CVA Axle ✅ Compatibility: Team Associated RC10 B74 Keep your B74 running smooth and race-ready with genuine Team Associated drivetrain components.

Read more less

Upgrade or replace your worn-out steering components with this genuine Team Associated RC10B74 Steering Bellcranks set. Designed specifically for the B74 platform, these bellcranks are precision-engineered to deliver smooth, accurate steering response on any track. 🔩 Key Features: Genuine Team Associated Factory Team parts Maintains optimal steering geometry Molded composite construction for lightweight durability Perfect fit for high-performance competition builds 📦 Includes: (1) Left Steering Bellcrank (1) Right Steering Bellcrank ✅ Compatibility: Team Associated RC10B74 May also fit other RC10B74-series variants Keep your steering system race-ready with fresh bellcranks designed to meet Factory Team standards.

Read more less

Upgrade your RC10B74 buggy with the Factory Team Carbon Rear Suspension Arms from Team Associated. These arms are crafted from lightweight and ultra-rigid carbon composite material, giving racers the precision, consistency, and responsiveness needed to compete at the highest levels. 📌 Key Features: Factory Team carbon construction for reduced weight and added stiffness Increased responsiveness and reduced flex under load Designed for competitive high-traction racing conditions Direct replacement for stock rear suspension arms 📦 Includes: (2) Carbon rear suspension arms (Left and Right) ✅ Compatibility: RC10B74 RC10B74.1 RC10B74.2 Engineered for racers who demand performance and reliability on the track.

Read more less

The XRAY XB4 2025 Composite Rear Lower Right Suspension Arm is precision-molded from graphite composite material for the ideal balance of durability and flex. Featuring a 3-hole shock mounting design, this arm allows fine tuning of rear suspension geometry for different track conditions. Engineered for maximum performance on high-grip surfaces, the updated design increases stability, consistency, and cornering response. Features: Genuine XRAY factory part for the XB4 2025 Molded from graphite composite for strength and controlled flex 3-hole shock mounting for suspension adjustability Right-side rear arm replacement Designed for high-grip track conditions Includes:(1) Composite Rear Lower Right Suspension Arm – Graphite (3-Hole) Compatibility: XRAY XB4 2025 May also fit earlier XB4 models (verify with setup/parts list)    

Read more less

Team Associated RC10B6.4 -1mm Scrub Caster & Steering Blocks (Carbon) [91985] 🛠️ Precision Meets Performance 💨 Upgrade your front end with this Carbon -1mm Scrub Caster & Steering Block Set for the RC10B6.4 and B6.4D. Built for racers who want rigidity, adjustability, and the ultimate in high-traction control. Carbon construction = serious stiffness. 🔥 ✅ Rigid carbon for a more responsive suspension✅ Includes multiple caster insert options for fine-tuning✅ -1mm scrub radius for quicker steering feel✅ Built for B6.4 / B6.4D platforms Includes:(2) Carbon Caster Blocks(4) Carbon Steering Blocks(2) +/- 0° Caster Inserts(2) +/- 2.5° Caster Inserts(2) +/- 5° Caster Inserts(2) Shims 📦 Part Number: 91985🚗 Brand: Team Associated

Read more less

This is a replacement Team Associated RC10B74 Hinge Pin Set. 

Read more less

Team Associated RC10B74 Factory Team LTC Metal Differential Rebuild Set. This is an optional part intended for the B74 series of buggies. Includes: (2) Differential side gears (4) Differential Spider gears (2) Outdrive shims (4) Spider gear shims COMPATIBILITY: Team Associated RC10 B74 OriginalTeam Associated RC10 B74.1Team Associated RC10 B74.1DTeam Associated RC10 B74.2Team Associated RC10 B74.2D

Read more less

1up Racing Pro Duty Equipment Case – Built for the Track, Ready for Anything 🔧 Protect your gear like a pro with the 1up Racing Pro Duty Equipment Case – the ultimate storage solution for racers who value durability, organization, and style. Whether you're hauling tools, electronics, or spare parts, this case is engineered to keep your essentials safe and scratch-free. 💼 Featuring a rigid outer shell, dense internal padding, and six customizable dividers, this case adapts to your setup with ease. Impact-absorbing foam on the top and bottom adds next-level protection, while the internal compartments and zippered pouch keep everything neat and accessible. ✨ Key Features: 🛡️ Heavy-Duty Shell with Dense Padding – Keeps your tools, chargers, and electronics safe📦 Adjustable Dividers – 6 foam inserts for a fully customizable interior layout🧵 Durable Black Fabric Interior – Clean, professional finish inside and out🧰 4 Tool Pouches + Zippered Pocket – Store scissors, pliers, leads, setup sheets, and more🧩 Impact-Absorbing Foam (Top & Bottom) – Superior protection during transport 📏 Dimensions: Interior Space: 23 x 20 x 7.5cm\ Dividers Included:✔️ (1) 23cm Divider✔️ (2) 12.5cm Dividers✔️ (3) 6.5cm Dividers 🎯 Built to Travel. Designed to Organize. Whether you're trackside or organizing your pit area at home, the 1up Racing Pro Duty Equipment Case keeps your essentials secure, accessible, and race-ready. 💡 Organize Like a Pro – Grab Your 1up Equipment Case Today!

Read more less

Team Associated Factory Team Carbon Front Gearboxes – RC10B74.2 Tunable Front-End Performance for Changing Track Conditions Unlock precise handling with the Factory Team Carbon Front Gearboxes for the RC10B74.2 and RC10B74.2D. This lightweight carbon-reinforced gearbox set offers both standard and +2mm ride height options, giving racers ultimate flexibility in front-end tuning for varying surfaces and setups. 🔩 Features: 🧱 Lightweight carbon composite material 📏 Includes both standard and +2mm height gearboxes 🔧 Covers included for both gearbox housings 🌀 Comes with sway bar bracket for fine handling adjustments 📦 Includes: (1) Standard Height Front Gearbox w/ Cover (1) +2mm Front Gearbox w/ Cover (1) Sway Bar Bracket ✅ Compatibility: Team Associated RC10B74.2 Team Associated RC10B74.2D 🎯 Optimize your front-end geometry for maximum track performance.

Read more less

Give your B74.2 the aerodynamic advantage it deserves with the JConcepts S15—a refined, high-performance body shell designed for peak competition. Inspired by the winning heritage of the Silencer series, the S15 introduces updated airflow features, improved chassis clearance, and stability enhancements tailored specifically for the Team Associated RC10 B74.2 platform. Available in Standard or Lightweight options to suit your setup and driving style. S15 Body Overview JConcepts engineered the S15 to complement the modern B74.2 chassis layout. This includes raised side-pods for compatibility with tall shorty packs and saddle configurations, as well as tuned aerodynamics for improved cornering and stability. Mid-body winglets and a rear stabilizer kick-up provide enhanced downforce, while the signature cockpit “shark fin” increases straight-line tracking and structural integrity. The result: a body that delivers balance, steering predictability, and high-speed stability across carpet, turf, and dirt surfaces. Key Features Precision fit for the Team Associated RC10 B74.2 Updated S15 aero package for improved stability and corner speed Forward cab bias for aggressive steering response Mid-body winglets & rear kick-up for added downforce Cockpit “shark fin” enhances tracking and rigidity Raised rear side-pods for modern battery layouts Clear polycarbonate with overspray protective film Available in Standard or Lightweight versions Includes (1) JConcepts RC10 B74.2 S15 Clear Buggy Body (1) Carpet Wing (1) Decal Sheet (1) Window Mask Set Note Body ships clear and unpainted Painted examples shown for reference only

Read more less

Dial in your suspension with Team Associated’s Factory Team 13mm shock pistons. The #91933 set features 2x1.7mm holes with a 2.5mm thick profile, providing a great tuning option for refining pack and rebound on modern high-performance off-road tracks. 📦 Includes: (2) FT 13mm Shock Pistons – 2x1.7mm hole layout 2.5mm thick ⚙️ Key Features: CNC-machined for ultra-precise damping consistency Designed for 13mm shock bodies used on AE’s latest platforms Ideal for high-traction surfaces needing tighter shock control Compatible with RC10B6.4, RC10B74.2, and similar vehicles 📌 Tuning Tip: Use 2x1.7mm pistons to increase damping over 2x1.8mm, providing more pack and control in bumpy or high-speed corners.

Read more less

Complete your sway bar setup or replace worn components with this genuine RC10B74 Anti-Roll Bar Hardware Set from Team Associated. Designed specifically for the B74 series, this hardware kit ensures your anti-roll bars function smoothly and securely. 🔧 Key Features: OEM replacement hardware for RC10B74 anti-roll bar system Includes mounting pieces and fastening components Precision fit for secure and reliable installation Ideal for fresh builds or routine maintenance 📦 Includes: Anti-roll bar mounting hardware (exact contents may vary) ✅ Compatibility: RC10B74 May fit other B74 platform variants with anti-roll bar setups Maintain consistent suspension balance and performance—use the right hardware for the job with this official Team Associated upgrade.

Read more less

🔧 Strong, Precise, Race-ReadyThe Team Associated RC10B84 Front Suspension Arms are precision-molded replacement components built to handle the rigors of competitive racing. Designed specifically for the B84 platform, these arms deliver the perfect balance of strength, flexibility, and lightweight performance to maintain consistent handling and durability under extreme conditions. ⚙️ Features: ✅ Direct fit replacement for RC10B84 ✅ Molded composite construction for durability and controlled flex ✅ Maintains proper suspension geometry for predictable handling ✅ Perfect for racers needing fresh arms or spares 📦 Includes: (1) Pair of Front Suspension Arms  

Read more less

🏆 Stronger, Straighter, FasterThe “A” Arm Mount for the RC10B84 is a precision CNC-machined aluminum upgrade that replaces the stock plastic piece. Built to handle the toughest racing conditions, this mount locks in suspension geometry for consistent camber and toe, helping your buggy track straighter and corner sharper. ⚙️ Features: ✅ CNC-machined aluminum for superior durability ✅ Precision hinge-pin alignment ensures consistent suspension setup ✅ Anodized finish resists wear and adds a pro look ✅ Direct replacement for the stock “A” mount 📦 Includes: (1) RC10B84 “A” Arm Mount 💡 Pro Tip: Combine the A, B, and C aluminum arm mounts for a fully upgraded rear suspension package — maximizing both strength and precision.  

Read more less

🔥 Big Power. Small Footprint.The Team Exalt 110W Digital Soldering Iron packs serious heat in a travel-friendly design. With lightning-fast heat-up, digital precision, and a built-in safety shutoff, this is your go-to soldering tool whether you’re at the track or at the bench. ⚡ Features: 110W power output for rapid heat-up Digital display with °F/°C readout Auto safety shutoff & sleep timer Ceramic heater with platinum temp sensor Plug-and-play AC design—no base station needed Compact, portable, and ready to travel 💡 Built for RC racers, builders, and field techs who demand pro-level performance in a portable package.

Read more less

This is a Reedy Flat Sensor Wire. The flat sensor wires that are included with the Reedy Sonic motor are now available separately in a variety of lengths to suit 1/10 and 1/8 applications! The flat design looks great and provides an extremely clean look. Choose from between 70mm and 270mm lengths.

Read more less

Team Associated 13mm Rear Shock Spring. These optional springs are intended for the Team Associated B6.4D and the B6.4. Package includes two springs. Effects of Shock Spring Changes  Shock Spring  Characteristic  Softer Increased Chassis Roll Increased Traction Better in Bumpy Conditions More Likely to Bottom Out  Stiffer Decreased Chassis Roll Decreased Traction Increased Responsiveness COMPATIBILITY: Team Associated RC10 B74.2Team Associated RC10 B74.2DTeam Associated RC10B6.4Team Associated RC10B6.4D

Read more less

Team Associated 13mm Front Shock Spring. These optional springs are intended for the Team Associated B6.4D and the B6.4. Package includes two springs. Effects of Shock Spring Changes  Shock Spring  Characteristic  Softer Increased Chassis Roll Increased Traction Better in Bumpy Conditions More Likely to Bottom Out  Stiffer Decreased Chassis Roll Decreased Traction Increased Responsiveness COMPATIBILITY: Team Associated RC10 B74.2Team Associated RC10 B74.2DTeam Associated RC10B6.4Team Associated RC10B6.4D

Read more less

Team Associated RC10B74.2 0 and 2mm Front Gearboxes. This is a replacement intended for the RC10B74.2 and B74.2D series of vehicles. Package includes one 0mm height front differential gearbox with cover and one 2mm height front differential gearbox with cover. COMPATIBILITY: Team Associated RC10 B74.2Team Associated RC10 B74.2D

Read more less

Team Associated RC10B74.2 Battery Mount Set. This is a replacement intended for the RC10B74.2 and B74.2D series of vehicles. Package includes battery mount parts tree, two rubber battery straps and mounting hardware. COMPATIBILITY: Team Associated RC10 B74.2Team Associated RC10 B74.2D

Read more less

Pro-Motion 2.2" Rear Buggy Wheels (4)Available in White (3050-W) or Yellow (3060-Y) Engineered for Speed. Built to Dominate. Give your buggy the winning edge with Pro-Motion’s 2.2" Rear Wheels, designed for today's high-traction tracks. These wheels feature a reinforced inner rib structure for added durability without the weight penalty. The lightweight design and precision molding ensure a true, balanced rotation—exactly what you need for consistent traction and razor-sharp control. ✅ Fits most 1/10 scale buggies with 2.2" rear wheels✅ Lightweight inner rib design for enhanced strength✅ High-durability construction for racing abuse✅ Built-in vent holes reduce tire distortion✅ Available in sleek White or Fluorescent Yellow 📦 Includes:(4) 2.2" Rear Buggy Wheels 💡 Pro Tip: Match with Pro-Motion front wheels for a full performance setup that looks as good as it drives.

Read more less