Traxxas 25-Tooth Pinion Gear (32-Pitch, 3mm Bore) – Part #10842⚙️ Dial In Your Speed. Smooth, Efficient Power Delivery. Upgrade or fine-tune your drivetrain with this Traxxas 25T pinion gear. Built for 3mm motor shafts and compatible with 32-pitch setups, it delivers solid acceleration and balanced top-end speed. Perfect for dialing in gearing to match your terrain or driving style. ✅ 25-tooth pinion✅ 32-pitch gear profile✅ Fits 3mm motor shafts✅ Hardened for long-lasting performance✅ Includes set screw for secure installation 📦 Includes: (1) 25T Pinion Gear (32P, 3mm bore) (1) Set Screw  

Read more less

⚡ Unleash the Full Potential of Your Traxxas Ride This Traxxas 2S 5000mAh LiPo battery with iD connector is built to deliver powerful punch and extended run time for your favorite Traxxas vehicles. Designed for maximum performance, this 25C battery gives you the acceleration, speed, and reliability you demand — all with the convenience of the Traxxas iD system for easy, foolproof charging. 🔋 Battery Specs: Type: LiPo Capacity: 5000mAh Voltage: 7.4V (2S) Discharge Rate: 25C Length: 137mm Width: 43mm Height: 24mm Weight: 9.9oz ✅ Features: Certified Traxxas iD-equipped for safe, easy charging Engineered for high performance and extended run time Fits Traxxas models perfectly — no modifications needed Delivers the power needed for peak speed and acceleration

Read more less

Get the performance and reliability you expect from Traxxas with the 5800mAh Power Cell 2S LiPo—a perfect balance of power, runtime, and safety for your Traxxas vehicle. 🔋 7.4V / 5800mAh / 25C Continuous Discharge🔌 Exclusive Traxxas iD Connector for simple, safe charging⚡ Max Burst Rate: 50C (290A)💪 Hard-wired 12AWG Maxx Cable for low resistance🏁 Designed for a perfect fit in Traxxas vehicles Dimensions: 137x25x43mmWeight: 308g ⚠️ Requires Traxxas iD charger only. Do not charge with any non-Traxxas charger. Boost your bash time with dependable power, rugged construction, and high-output delivery—Traxxas style.

Read more less

Power up your ride with serious runtime and punch! The Traxxas Power Cell 7600mAh 2S LiPo delivers high-capacity performance with rugged construction and easy plug-and-go charging through the Traxxas iD system. 🔋 7.4V / 7600mAh / 25C Continuous🔌 iD Connector for safe, simple charging🔥 Max Burst Rate: 50C (380A)⚡ Maxx Cable 12AWG wiring for low resistance🏁 Optimized fit for Traxxas models like Slash & Slash 4x4💡 Semi-rigid construction – no hard case needed Dimensions: 155x27x43mmWeight: 390g ⚠️ Note: Must be charged with a Traxxas iD charger only. The go-to battery for racers and bashers who want dependable power, long runtimes, and Traxxas factory fit and finish.  

Read more less

  Keep your TRX-4M running strong with this genuine Traxxas 2S LiPo battery! Compact, lightweight, and built for performance, it delivers consistent 7.4V power and 750mAh capacity with a 20C discharge rate—perfect for extended crawling adventures. ✅ Capacity: 750mAh✅ Voltage: 7.4V (2S)✅ Discharge Rate: 20C✅ Connector: Traxxas High-Current✅ Compatible With: TRX-4M Engineered by Traxxas for optimal runtime, reliability, and fit in your TRX-4M.

Read more less

📡🏁 Advanced Control for Your Traxxas RC Vehicle The Traxxas 3-Channel Wireless-Ready TQi 2.4GHz Transmitter delivers the precision, reliability, and comfort needed to get the most from your Traxxas vehicle. Designed for long-range performance and responsive control, the TQi system features automatic model recognition, an ergonomic design, and compatibility with the Traxxas Link™ Wireless Module for expanded tuning and telemetry capabilities. Whether you're replacing a transmitter or upgrading your setup, the TQi provides the dependable performance Traxxas is known for. 🏁 About the TQi 3-Channel Transmitter 📡 Reliable 2.4GHz Performance The TQi radio system provides a powerful long-range 2.4GHz signal for smooth, interference-resistant operation and precise vehicle control. 🚗 Automatic Model Recognition Store settings for multiple Traxxas Link-enabled models. The transmitter automatically recognizes your vehicle and recalls the appropriate settings, making it easy to switch between compatible models. 📱 Wireless-Ready Expansion Install the optional Traxxas Link™ Wireless Module to unlock additional tuning features through the free Traxxas Link app, including expanded setup options and telemetry support on compatible vehicles. ✋ Comfortable Ergonomic Design The lightweight pistol-grip transmitter is designed for extended driving sessions, while the internal antenna eliminates the risk of antenna damage. 🔧 Features ✔ Genuine Traxxas replacement transmitter✔ 3-channel 2.4GHz radio system✔ Wireless-Ready design✔ Automatic model recognition for multiple Traxxas Link-enabled vehicles✔ Long-range, high-output 2.4GHz signal✔ Comfortable ergonomic pistol-grip design✔ Internal protected antenna✔ Compatible with the optional Traxxas Link™ Wireless Module 📦 Includes (1) Traxxas 3-Channel Wireless-Ready TQi 2.4GHz Transmitter 🚗 Compatibility Compatible with many Traxxas surface vehicles using compatible TQi receivers and Traxxas Link-enabled systems. ⚠️ Notes Genuine Traxxas replacement part. This listing is for the transmitter only. Receiver is not included. Traxxas Link™ Wireless Module (sold separately) is required for Bluetooth connectivity and use with the Traxxas Link mobile app. Verify compatibility with your specific Traxxas vehicle before pairing. Traxxas 3-Channel Wireless-Ready TQi 2.4GHz Transmitter (6529X) 📡🏁 Advanced Control for Your Traxxas RC Vehicle The Traxxas 3-Channel Wireless-Ready TQi 2.4GHz Transmitter delivers the precision, reliability, and comfort needed to get the most from your Traxxas vehicle. Designed for long-range performance and responsive control, the TQi system features automatic model recognition, an ergonomic design, and compatibility with the Traxxas Link™ Wireless Module for expanded tuning and telemetry capabilities. Whether you're replacing a transmitter or upgrading your setup, the TQi provides the dependable performance Traxxas is known for. 🏁 About the TQi 3-Channel Transmitter 📡 Reliable 2.4GHz Performance The TQi radio system provides a powerful long-range 2.4GHz signal for smooth, interference-resistant operation and precise vehicle control. 🚗 Automatic Model Recognition Store settings for multiple Traxxas Link-enabled models. The transmitter automatically recognizes your vehicle and recalls the appropriate settings, making it easy to switch between compatible models. 📱 Wireless-Ready Expansion Install the optional Traxxas Link™ Wireless Module to unlock additional tuning features through the free Traxxas Link app, including expanded setup options and telemetry support on compatible vehicles. ✋ Comfortable Ergonomic Design The lightweight pistol-grip transmitter is designed for extended driving sessions, while the internal antenna eliminates the risk of antenna damage. 🔧 Features ✔ Genuine Traxxas replacement transmitter✔ 3-channel 2.4GHz radio system✔ Wireless-Ready design✔ Automatic model recognition for multiple Traxxas Link-enabled vehicles✔ Long-range, high-output 2.4GHz signal✔ Comfortable ergonomic pistol-grip design✔ Internal protected antenna✔ Compatible with the optional Traxxas Link™ Wireless Module 📦 Includes (1) Traxxas 3-Channel Wireless-Ready TQi 2.4GHz Transmitter 🚗 Compatibility Compatible with many Traxxas surface vehicles using compatible TQi receivers and Traxxas Link-enabled systems. ⚠️ Notes Genuine Traxxas replacement part. This listing is for the transmitter only. Receiver is not included. Traxxas Link™ Wireless Module (sold separately) is required for Bluetooth connectivity and use with the Traxxas Link mobile app. Verify compatibility with your specific Traxxas vehicle before pairing.

Read more less

Traxxas 3000mAh 7.4V 2-Cell LiPo Battery w/ iD® Connector (Part #2827X) 🔋Compact 2S Power for Lightweight Performance The Traxxas 3000mAh 2S LiPo battery is a lightweight, reliable power source ideal for vehicles where space and weight matter. Equipped with the Traxxas iD® connector, this pack simplifies charging by automatically configuring settings when used with a Traxxas iD-compatible charger. Great for hobbyists looking for consistent performance in a compact form. ⚡ Features: 🔋 3000mAh Capacity – Balanced for light-duty bashing or casual driving 🔌 7.4V 2-Cell (2S) Configuration – Delivers smooth, consistent 2S performance 🔗 Traxxas iD® Connector – Auto-detects cell count and chemistry for worry-free charging 🧊 Hard Case Shell – Protects the battery during use and transport 📏 Slightly Smaller Footprint – Ideal for tighter battery compartments 📦 Specifications: Voltage: 7.4V Cell Count: 2S (2-cell LiPo) Capacity: 3000mAh Connector Type: Traxxas High-Current iD® Perfect for casual running, lightweight vehicles, or smaller 1/10 models.Use only with Traxxas iD®-compatible chargers to ensure safe, optimized charging. 🔌✅

Read more less

Traxxas 30° Caster Blocks (2) – PART 3632 Keep your suspension strong and steering responsive with this set of 30° caster blocks from Traxxas. Whether you're replacing worn parts or dialing in your setup, these precision-molded blocks are built tough to handle the rigors of high-speed off-road action. Features: Genuine Traxxas replacement part Designed for consistent steering geometry and durability 30° caster angle for balanced handling on a variety of surfaces Includes left and right side caster blocks Upgrade with confidence—perfect for restoring performance and getting back on track fast.

Read more less

Traxxas 32P Hardened Steel Pinion Gear (31T, 5mm Bore) – Part #5638⚙️ Stronger. Smoother. Built for Brushless. The Traxxas 31-Tooth Pinion Gear is built for performance and durability. Compatible with 32-pitch setups (0.8 metric pitch), this pinion is precision-cut from hardened steel and designed to fit motors with a 5mm shaft. Perfect for high-power RC builds demanding reliable gearing under pressure. ✅ 32-pitch / 0.8 mod compatibility✅ Hardened steel construction✅ 5mm bore for brushless motor shafts✅ Ideal for Slash 4X4, E-Revo, and other high-output platforms 📦 Includes: (1) 31T Hardened Steel Pinion Gear (1) Set screw  

Read more less

Traxxas 32P Hardened Steel Pinion Gear (34T, 5mm Bore) – Part #5639⚙️ Built to Handle Brutal Power. The Traxxas 34T Hardened Steel Pinion Gear is designed for serious torque and high-performance applications. Made from tough hardened steel, this 32-pitch gear is perfect for 1/8 and high-power 1/10 scale builds using motors with 5mm shafts. When you need dependable gearing that can take the heat—this is the upgrade. ✅ 32 pitch for high-power drivetrain setups✅ Hardened steel for extreme durability✅ 5mm bore fits most 1/8 brushless motors✅ Ideal for Slash 4X4, E-Revo, and more with 5mm shafts 📦 Includes: (1) 34T Hardened Steel Pinion Gear (1) Set screw

Read more less

Upgrade your drivetrain with Traxxas 32P Heavy Duty Pinion Gears, built tough from hardened steel for maximum durability and long-lasting performance. Available in a range of tooth counts from 12T to 22T, these 32-pitch pinions are perfect for high-power setups and intense off-road action. 🔩 Precision-machined hardened steel🔩 Perfect for brushless power systems🔩 Includes set screw for secure installation🔩 Available sizes: 12T through 22T🔩 Fits 3mm motor shafts Includes: (1) Steel Pinion Gear (Choose Tooth Count) (1) Set Screw Part Numbers: 3942X–3952X (select by tooth count) Built for strength. Made for speed. Trusted by Traxxas.

Read more less

Traxxas 34-Tooth Pinion Gear (1.0 Mod, 5mm Bore) – Part #6493⚙️ Max Out Top Speed. Built for Brutal Brushless Power. The Traxxas 34T Pinion Gear is precision machined for smooth performance and maximum efficiency. With a 1.0 metric pitch and 5mm bore, it’s made to fit high-powered brushless setups and withstand serious speed and torque. Perfect for high-speed runs and gear ratio tuning. ✅ 34-tooth gear for higher top-end speed✅ 1.0 Mod pitch for strength and durability✅ Fits 5mm motor shafts (ideal for brushless systems)✅ Machined steel for long-lasting wear resistance✅ Includes set screw 📦 Includes: (1) 34T Pinion Gear (1.0 Mod, 5mm bore) (1) Set Screw

Read more less

Traxxas 36mm Camber Link Turnbuckles (2) – Part 2443Fine-Tune Your Ride Height & Camber. This replacement camber link turnbuckle set includes two 36mm steel turnbuckles, designed specifically for the Traxxas Bandit. Easily adjust your rear camber angle to improve handling, cornering grip, and tire wear. ✅ Direct fit for Traxxas Bandit✅ Includes two 36mm steel turnbuckles✅ Precision threads for smooth adjustment✅ Strong steel construction – durable and race-tested✅ Adjustable with a turnbuckle wrench (sold separately) 📦 Includes: (2) 36mm Camber Link Turnbuckles Part #: 2443 💡 Pro Tip: Pair with upgraded rod ends or toe links for full tuning flexibility and improved suspension geometry.

Read more less

Turnbuckle Overview:This is a replacement set of camber link turnbuckles designed for select Traxxas models. Pre-assembled with rod ends and hollow balls, they provide easy installation and precise suspension adjustment. 🔧 Key Features ✔ 39mm camber link turnbuckles✔ 69mm center-to-center length✔ Pre-assembled with rod ends and hollow balls✔ Includes left and right side✔ Allows precise camber adjustment✔ Direct fit replacement 📦 Includes (1) Left Turnbuckle Assembly (1) Right Turnbuckle Assembly 🚗 Compatibility Traxxas Drag Slash Traxxas Hoss Traxxas Nitro Slash Traxxas Rally Traxxas Rustler 2WD Traxxas Rustler 4x4 Traxxas Slash 2WD Traxxas Slash 4x4 Traxxas Slash 4x4 Ultimate Traxxas Stampede 2WD Traxxas Stampede 4x4 Ideal for replacing worn or bent links, these turnbuckles help maintain proper suspension geometry and allow for accurate camber tuning.  

Read more less

Traxxas 39mm Front Aluminum Camber Link – Part 3737 (Red or Blue)Tuned Precision. Aluminum Strength. Color to Match Your Build. The Traxxas 39mm front camber link turnbuckle is built from lightweight, anodized aluminum to provide extra strength and adjustability over stock plastic links. Whether you're upgrading for durability or adding style, this part delivers both. ✅ Available in Red or Blue anodized finish – match your rig’s style✅ Assembled with rod ends & hollow balls – ready to install✅ 39mm length – direct fit for Traxxas front suspension✅ Aluminum construction – stiffer, more durable than stock✅ Perfect for tuning front camber on high-performance setups✅ See Part 3741X for complete front/rear camber link set 📦 Includes: (1) 39mm Aluminum Camber Link Turnbuckle (Assembled) (2) Hollow Balls Part #: 3737 OR 3737A (choose Red or Blue) 💡 Pro Tip: Pair with aluminum rear camber links and toe links for a fully upgraded suspension geometry setup.  

Read more less

Traxxas Power Cell LiPo Battery (3S, 11.1V, 6400mAh, 25C) w/iD ConnectorBig Power. Big Capacity. Built for Traxxas Performance. Battery Overview:When speed, runtime, and reliability matter, the Traxxas 3S 6400mAh Power Cell LiPo delivers. This high-performance 11.1V LiPo battery is engineered specifically for Traxxas vehicles and is optimized to extract every ounce of performance from your 3S-compatible model. Whether you're chasing top speed or extended bash sessions, this pack is your power advantage. NOTE: VXL Brushless models are compatible with 2S or 3S LiPo XL-5 Brushed models are compatible with 2S LiPo ONLY Requires a Traxxas iD® Charger for safe and proper charging Key Features:✅ 6400mAh Capacity – Massive runtime for long sessions✅ 25C Discharge Rate – Delivers up to 160A continuous power✅ Hard-Wired iD Connector – Simplifies charging and ensures correct settings✅ High-Current Traxxas Connector – Virtually zero voltage loss✅ Center Wire Exit – Perfect fit for Traxxas chassis layouts✅ Semi-Rigid Construction – Greater capacity in a more compact size✅ Maxx Cable® 12AWG Wire – Maximum current flow, ultra-flexible silicone insulation✅ Lifetime Battery Exchange Program – Traxxas has your back, even after the warranty What Makes it Special: Built for Brushless Power: Pushes 3S-capable Traxxas vehicles to their limit No Foam Blocks Needed: Designed to factory-fit Slash, Slash 4x4, and other Traxxas platforms Safe & Simple Charging: iD technology eliminates setup guesswork Visible Puffing Protection: Semi-rigid packs reveal damage before it becomes dangerous Specs: Type: LiPo Voltage: 11.1V (3S) Capacity: 6400mAh Continuous Discharge: 25C (160A) Max Burst Rate: 50C (320A) Watt Hours: 71.04Wh Charge Rate: 2C Max (12.6A) Dimensions: 138 x 41 x 43mm Weight: 17.7oz (502g) ⚠️ IMPORTANT: For Traxxas iD Chargers ONLY NEVER charge with a non-iD charger  ALWAYS use models with Low Voltage Detection enabled

Read more less

⚠️ Important Compatibility Note:• Traxxas VXL Brushless models = 2S & 3S LiPo compatible• Traxxas XL-5 Brushed models = 2S LiPo ONLYBe sure to select the correct battery for your vehicle. The Traxxas 3S 11.1V 5000mAh 25C Power Cell LiPo (2872X) delivers the extreme punch, runtime, and reliability needed for high-performance Traxxas vehicles. Designed exclusively for Traxxas models, this pack features the patented Traxxas iD High-Current Connector, ensuring easy, automatic, and safe balance-charging with Traxxas iD chargers. Built with premium low-resistance cells, durable construction, and heavy-duty wiring, this 3S pack unleashes the full potential of VXL Brushless systems — giving your truck, buggy, or boat incredible acceleration and top speed. Features 3S (11.1V) 5000mAh capacity for long run times 25C continuous / 50C burst discharge rate Traxxas iD High-Current Connector – no external balance wires Requires a Traxxas iD charger for proper, safe charging Premium low-resistance cells for maximum punch 12-gauge flexible Maxx Cable wiring Oversized cell tabs for improved efficiency Semi-rigid construction for durability and easier pack inspection Center-exit wiring for proper fitment in Traxxas chassis Covered by the Traxxas Lifetime Battery Exchange Program Traxxas iD Charging System Traxxas iD chargers automatically detect your iD battery, set the correct charge parameters, and balance the pack internally — giving you the safest and simplest charging experience in RC.Just plug in and walk away. Specifications Type: LiPo Capacity: 5000mAh Voltage: 11.1V (3-Cell) Continuous Discharge: 25C (125A) Burst Discharge: 50C (250A) Watt Hours: 55.5Wh Charge Rate: 1C (5A) Max Charge Rate: 2C (10A) Dimensions: 155 × 26 × 44 mm Weight: 13.3 oz (376 g) Connector: Traxxas iD High-Current Includes (1) Traxxas 3S 5000mAh LiPo Battery (2872X) ⚠️ Charging Safety This battery MUST be charged with a Traxxas iD charger.Do not attempt to charge with non-Traxxas chargers, balance boards, or adapters. Doing so can result in fire, damage, or voided warranty.

Read more less

Keep your engine secure with this pack of four 3x10mm flat head hex screws from Traxxas. Designed specifically for engine mount applications, these screws offer a flush fit and solid hold. A must-have for maintenance or replacement in your Traxxas nitro models. ✅ Flat head for flush engine mount fit✅ 3x10mm hardened steel construction✅ Hex drive for easy installation✅ Genuine Traxxas part Includes: (4) 3x10mm Flat Head Engine Mount Hex Screws Part #: 4859 Perfect fit. Proven durability. Traxxas quality.    

Read more less

Traxxas 3x10mm Countersunk Machine Screws (6) – Part 3177Flush Fit. Clean Finish. Reliable Hold. The Traxxas 3x10mm countersunk machine screws are ideal when you need a flat, snag-free finish on your chassis or components. Perfect for securely mounting parts where a flush surface is critical. ✅ Includes 6 countersunk machine screws✅ Size: 3x10mm✅ Precision-threaded for secure fitment✅ Countersunk head – sits flush for clean installs✅ Great for chassis plates, skid plates, and more 📦 Includes: (6) 3x10mm Countersunk Machine Screws Part #: 3177 💡 Pro Tip: Use with countersunk washers or directly into flat surfaces where clearance matters.

Read more less

Traxxas 3x10mm Washer-Head Machine Screws (6) – Part 3193Secure Fit. Wider Hold. Versatile Length. The Traxxas 3x10mm washer-head machine screws are a go-to solution when you need a reliable fastener with added grip. The integrated washer-style head distributes pressure evenly — ideal for fastening into plastic or securing sensitive components. ✅ Includes 6 washer-head machine screws✅ Size: 3x10mm – versatile length for multiple RC applications✅ Integrated washer head – prevents pull-through and distributes load✅ Standard 3mm thread – fits most 1/10 scale Traxxas vehicles✅ Perfect for mounting electronics, suspension parts, and body panels 📦 Includes: (6) 3x10mm Washer-Head Machine Screws Part #: 3193 💡 Pro Tip: Ideal for use in plastic components where added surface area helps prevent damage.  

Read more less

Whether you're replacing worn-out hardware or stocking up your pit box, these genuine Traxxas 3x12mm button head machine screws are a must-have! Made with precision and durability in mind, they're perfect for securing various components on your Traxxas RC vehicles. ✅ Includes: 6 screws✅ Thread: Machine✅ Size: 3x12mm✅ Fits: Virtually any Traxxas vehicle – including Revo, Slash, Rustler, TRX-4, and more✅ Use for: Repairs, upgrades, or custom builds Built by Traxxas for Traxxas – engineered to fit right every time.    

Read more less

These 3x12mm countersunk machine screws from Traxxas are perfect for flush-mount applications where a clean, low-profile finish is needed. With Phillips drive heads for easy installation, they’re ideal for chassis and other flat-surface mounting tasks. Features:• 3x12mm steel machine screws• Countersunk heads for flush fit• Phillips drive for standard screwdriver compatibility• Great for chassis and hardware installations• Genuine Traxxas hardware for reliable performance Includes:• (6) 3x12mm Countersunk Machine Screws (Phillips Drive)Part Number: 3178 Tighten up your build with dependable, flush-fitting Traxxas screws.  

Read more less

The Traxxas 3x12mm Shoulder Screws (Ultra Shocks) are genuine replacement parts designed specifically for securing the shock caps and rod ends on Traxxas Ultra Shocks. Made from high-quality steel, these precision shoulder screws ensure smooth operation and a secure fit, keeping your suspension performing at its best. Features: Genuine Traxxas replacement hardware Designed for use with Traxxas Ultra Shocks Precision shoulder design ensures smooth movement and durability Strong steel construction for long-lasting performance Includes:(6) 3x12mm Shoulder Screws Compatibility: Traxxas Ultra Shocks Fits various Traxxas models equipped with Ultra Shocks, including Slash, Rustler, Stampede, and Bandit

Read more less

Keep your Traxxas vehicle race-ready with this genuine Traxxas 3x15mm Button Head Screw Set. Perfect for maintenance or repairs, these durable steel screws are precision-made for a perfect fit in your model. Features: Genuine Traxxas replacement hardware Durable steel construction for long-lasting strength Ideal for repairs, maintenance, and custom builds Precision fit ensures reliable performance Includes:(6) 3x15mm Button Head Screws Compatibility: Traxxas Rustler Traxxas Stampede Also fits various other Traxxas 1/10-scale models    

Read more less

Traxxas 3x15mm Countersunk Machine Screws (6) – Part 3179Longer Reach. Flush Fit. Factory Reliable. The Traxxas 3x15mm countersunk machine screws are designed for secure fastening where a flush surface is needed — with a little more length for deeper mounting applications. ✅ Includes 6 precision-machined screws✅ Size: 3x15mm – great for thicker components or multiple layers✅ Countersunk head – installs flush for a smooth, clean finish✅ Standard 3mm thread – fits most Traxxas 1/10 scale builds✅ Perfect for chassis, skid plates, and hardware upgrades 📦 Includes: (6) 3x15mm Countersunk Machine Screws Part #: 3179 💡 Pro Tip: Ideal for use in areas where ground clearance matters or where screws pass through multiple materials.

Read more less

Keep your Traxxas vehicles tightly assembled with the Traxxas 3x15mm Washer Head Phillips Screws. These high-quality screws feature an integrated washer-style head to evenly distribute load and prevent damage to mounting surfaces—perfect for general chassis, suspension, and body applications. 🔥 Key Features: Genuine Traxxas OEM replacement hardware 3x15mm Phillips head design for quick, easy installation Washer-style flange head spreads pressure to protect plastic parts Made from hardened steel for long-lasting durability Ideal for maintenance, repairs, and custom builds ✅ Compatibility: Fits a wide range of Traxxas 1/10 and 1/16 scale vehicles Commonly used in Slash, Rustler, Bandit, Stampede, and other Traxxas models 📦 Includes: (6) 3x15mm washer head Phillips screws ⚠️ Tip:When installing into plastic components, thread screws gently by hand first to ensure proper alignment and prevent stripping.

Read more less

Traxxas 3x18mm Round-Head Machine Screws (6) – Part 2565Reliable Hardware. Precision Fit. The Traxxas 3x18mm round-head machine screws are perfect for replacing lost hardware or stocking your pit box. Built for a secure fit and clean finish, these screws are ideal for a wide range of RC assembly applications. ✅ Includes 6 round-head machine screws✅ Size: 3x18mm✅ Standard thread – compatible with most 1/10 Traxxas builds✅ Ideal for suspension, body, and chassis components✅ OEM quality for reliable performance 📦 Includes: (6) 3x18mm Round-Head Machine Screws Part #: 2565 💡 Pro Tip: Always keep a few spare hardware packs on hand for quick repairs and build adjustments.  

Read more less

Secure your components with confidence using Traxxas 3x20mm Countersunk Machine Screws. Featuring hex drive heads and a flush-fit countersunk design, these screws are perfect for applications where a smooth surface is essential. Features:• 3x20mm steel machine screws• Countersunk heads for flush mounting• Hex drive for reliable installation• Ideal for chassis, suspension, and flat-surface mounting• Genuine Traxxas hardware Includes:• (6) 3x20mm Countersunk Machine ScrewsPart Number: 2590 Perfect fit, strong hold—upgrade or replace with genuine Traxxas quality.      

Read more less

Traxxas 3x25mm Round-Head Machine Screws (6) – Part 2569Long Reach. Rock-Solid Hold. The Traxxas 3x25mm round-head machine screws are ideal for applications that require extra length without sacrificing strength or fit. Perfect for securing larger components or layering through thicker mounts. ✅ Includes 6 round-head machine screws✅ Size: 3x25mm – longer length for deeper mounting points✅ Durable steel construction – built to last under stress✅ Compatible with standard 3mm thread applications✅ Fits many Traxxas 1/10 scale models 📦 Includes: (6) 3x25mm Round-Head Machine Screws Part #: 2569 💡 Pro Tip: Match with washers or spacers to create rock-solid mounting solutions for electronics, bumpers, and more.    

Read more less

🔩 Strong, reliable fasteners for your Traxxas builds. This pack of Traxxas 3x30mm Button Head Machine Screws is perfect for repairs, upgrades, or custom builds. Made from durable steel and precision-threaded, they’re compatible with a wide range of Traxxas models, including the Revo. ✅ Durable steel construction✅ Precision M3 threading✅ Button head design for a smooth finish✅ Fits many Traxxas vehicles, including the Revo 📦 Includes:• (6) 3x30mm Button Head Machine Screws    

Read more less

Traxxas 3x8mm Button Head Machine Screws (6) – Part #2576🔩 Essential Hardware. Universal Fit. Keep your rig dialed with this 6-pack of Traxxas 3x8mm Button Head Screws. Designed for a clean, low-profile finish and built to handle tough conditions, these machine screws are perfect for a wide range of RC applications—including the Traxxas Revo and beyond. ✅ Button head design for a sleek and secure hold✅ Machine thread for metal or tapped plastic✅ Universal fit across many Traxxas vehicles✅ A great go-to screw for any pit box 📦 Includes: (6) 3x8mm Button Head Machine Screws 

Read more less

Traxxas 3x8mm Flat Head Screw (6) (VXL) – Part #3931🔩 Secure Fit. Clean Finish. The Traxxas 3x8mm Flat Head Screws are precision-machined for a flush, low-profile installation. Ideal for use in VXL and other Traxxas vehicles, these flat head screws ensure a snug, countersunk fit for components where a smooth finish is essential. ✅ Perfect for flush-mount applications✅ 3x8mm metric sizing✅ Flat head design for clean installation✅ Genuine Traxxas quality✅ Great for chassis, body panels, and more 📦 Includes: (6) 3x8mm Flat Head Screws 💡 Pro Tip: Always check your manual for proper screw placement and thread-lock recommendations for metal-on-metal applications.  

Read more less

Traxxas 3x8mm Washer-Head Machine Screws (6) – Part 3185Built-In Grip. Extra Hold. Compact Size. The Traxxas 3x8mm washer-head machine screws provide a wider contact surface for more secure fastening — without needing a separate washer. Ideal for mounting components where extra grip is needed in a tight space. ✅ Includes 6 washer-head machine screws✅ Size: 3x8mm – compact length for low-clearance installs✅ Washer-style head – spreads load, prevents pull-through✅ Standard 3mm thread – compatible with most Traxxas builds✅ Perfect for mounting electronics, linkages, and body parts 📦 Includes: (6) 3x8mm Washer-Head Machine Screws Part #: 3185 💡 Pro Tip: Great for plastic parts where larger heads reduce the risk of cracking or stripping.  

Read more less

  Bulkhead Overview:This is a replacement front bulkhead designed for the Traxxas 4-Tec 2.0 platform. It restores structural support to the front end and ensures proper alignment of suspension and drivetrain components. 🔧 Key Features Replacement front bulkhead Maintains chassis integrity and alignment Direct fit Traxxas part 📦 Includes (1) Front Bulkhead 🚗 Compatibility Traxxas 4-Tec 2.0 Ideal for replacing worn or damaged components, this bulkhead helps keep your 4-Tec 2.0 running straight and performing as intended.

Read more less

  This is a pack of four replacement Traxxas 4-Tec 2.0 Shock Caps. These caps feature installed eyelets. COMPATIBILITY: Traxxas 4-Tec 2.0 Traxxas Hoss Traxxas Rustler 4x4

Read more less

Traxxas 47mm Front Camber Link Turnbuckles (2) – Part 2444Tighten Up Your Front-End Geometry. The Traxxas 47mm Front Camber Link Turnbuckle Set is a direct replacement for the front camber links on the Traxxas Bandit. These adjustable steel turnbuckles allow you to fine-tune your camber for better cornering, tire contact, and front-end responsiveness. ✅ Designed specifically for the Traxxas Bandit (front suspension)✅ Includes two 47mm steel turnbuckles✅ Smooth-threaded for precise alignment changes✅ Heavy-duty steel construction – reliable and durable✅ Adjustable with a turnbuckle wrench (sold separately) 📦 Includes: (2) 47mm Front Camber Link Turnbuckles Part #: 2444 💡 Pro Tip: Combine with the 36mm rear turnbuckles (Part 2443) for full camber control front and rear.

Read more less