This is the JConcepts 85mm Aluminum Camber Gauge. A successful off-road racing program requires precise and accurate setup. Machined from billet aluminum material, the JConcepts ride height gauge is a high spec, detailed instrument that provides the precision your car deserves. The high polish, laser etched gauge features graduated measurements from -10 to +10 degrees for a complete range of camber adjustments. The camber gauge is pre-assembled with 4mm hardware for the pivot and thumbscrew as the setting knob. The structure features chamfered silver edging, highlighting the design. The alignment arm on the gauge is heavily chamfered which creates the perfect touch point against the tire and wheel. Each gauge comes in a latch box with foam insert which fits snugly around the instrument with heavy cushion. When racing gets serious, get precise with JConcepts.The gauge operates with 2 pivoting pieces which can be secured by using the thumbscrew. Checking the camber starts by first setting the vehicle on a flat surface with the correct ride height and viewing, by eye, the front-end of the vehicle. If the visual camber is close, slide the gauge over to the base of the front tire and pivot the arm up until it touches the tire or wheel surface. At the touch point, secure the thumb screw on the gauge and check the etched marking. Adjust the camber link turnbuckles and repeat for all 4 corners until the desired camber is achieved.To set camber, secure the thumbscrew on the etched number which is preferred. Slide the gauge over to the base of the front tire and watch for the touch point of the gauge against the tire. If the gauge touches at the top first you must add negative camber to get within the range of your setting. If the gauge touches at the bottom first you’ll need to add positive camber to move within range. After adjustments are made, fine tune until the tire rests top and bottom against the gauge and repeat for all 4 corners until the desired camber is achieved.Features: Pre-assembled, lightweight, aluminum construction Available in blue or black anodizing Laser etched graduated measurements Highly chamfered alignment arm as a touch off point Chamfer highlighted edging Included latch box with foam cushion NOTE: Changing ride height will also change your camber. If you make a change to the ride height of the chassis you will need to re-adjust the camber.
This is the ProTek R/C Aluminum Camber Gauge is a precision machined tool that allows for quick and easy camber checks for everything from 1/10 on road, to 1/8 truggy. Lightweight and easy to use this camber gauge features a laser engraved 117mm scale on the side to measure tire height, as well as a +5 to -12 degree scale for measuring camber. When it comes to high quality products that are backed by incredible customer support, ProTek R/C has you covered with the gear you need to keep your chassis dialed and race ready. Features: Precision machined aluminum Measures Laser engraved scale on both sides for easy viewing Great for 1/10 on road, to 1/8 truggy and everything in between 117mm max tire height Measure camber from within a +5 to -12 degree range
This is the Precision Monster Truck Camber Gauge from RPM. This new camber gauge offers monster truck owners the chance to perfectly tune the handling and performance of their trucks! It’s capable of measuring the camber angle on tires up to 6.5 inches or taller and as small as 2 inches in diameter. And it can measure angles up to 10 degrees positive and negative.Features: Taller design and large capacity for monster truck owners Accuracy within 1/2 of a degree Measures up to 10 degrees
Team Associated B6 Steering Assembly. This is the replacement steering assembly for the RC10 B6 and B6D buggies. Package includes right and left side steering bellcranks, steering rack and steering bellcrank brace. COMPATIBILITY: Team Associated RC10 SC6.1Team Associated RC10 SC6.2Team Associated RC10 T6.2Team Associated RC10B6 OriginalTeam Associated RC10B6.1Team Associated RC10B6.1 Factory LiteTeam Associated RC10B6.1DTeam Associated RC10B6.2Team Associated RC10B6.2DTeam Associated RC10B6.3Team Associated RC10B6.3DTeam Associated RC10B6D
9’ Long Servo Tape Double Sided Clear 1”W x 108”L 25mm Wide Roll Size: 55mm Diameter 1mm Thick Ultimate adhesion, easy peel off
The V-Force Designs 14-20mm Ride Height Gauge is a handy tool to accurately check your vehicle's ride height. This gauge features a clicker style cam detent system that provides precision adjustment from 14mm to 20mm in 1mm increments. CNC machined from T6 7075 aluminum, the gauge boasts a large diameter base, knurled edges for easy adjustment and a laser engraved scale for identification of the settings. Package includes one ride height gauge. To use, simply twist the gauge to the desired height and slide it under the model. If the chassis does not sit flush with the desired setting, make adjustments to ride height until the gauge slides under the chassis with no gap at the top. Features: Machined from T6 7075 aluminum Measures 14-20mm in 1mm increments Clicker style cam detent system provides precision adjustment knurled edges for easy adjustment Laser engraved scale
This is a Team Losi Racing 22T 2.0 Complete CVA Driveshaft Set. Package includes all the parts needed to build two complete driveshafts, as well as a tube of blue thread lock and two aluminum spacers.
Team Losi Racing 22 4.0 Battery Mount Set. This is the replacement battery mount. Package includes the parts needed to build both types of battery mount. COMPATIBILITY: Losi 22 4.0Losi 22 4.0 SPEC-RacerLosi 22T 4.0
The V-Force Designs 20-30mm Ride Height Gauge is a very handy tool to accurately check your vehicles ride height. This gauge features a clicker style cam detent system that provides precision adjustment from 20mm to 30mm in 1mm increments. CNC machined from T6 7075 aluminum, the gauge boasts a large diameter base, knurled edges for easy adjustment and laser engraved marks for identification of the settings. Package includes one ride height gauge.Features: Machined from T6 7075 aluminum Measures 20-30mm in 1mm increments Clicker style cam detent system provides precision adjustment knurled edges for easy adjustment Laser engraved scale
Black Aluminum Front Knuckles (Pair), for Traxxas Slash 4x4